|
#21
|
||||
|
||||
![]() Quote:
![]()
__________________
Stevie Brew [email protected] http://www.oople.com/forums/showthre...hlight=stegger |
#22
|
||||
|
||||
![]()
Because I ordered them a while ago and got mates running the car too, so it's sort of for them too.
I doubt I'll be keeping the car anyway. |
#23
|
||||
|
||||
![]()
WOW......after reading this thread I cannot believe racers are breaking sooo much on there 210's
![]() I've ran mine (mainly indoors) on a tight track where there is always contact and have yet to break anything! and was at Broxtowe yesterday, raced all day and even had a off at the end of the straight (on the banked corner) and didnt break a thing.....and I aint the best driver out there (my results show this ![]() Although now I've replied to this thread I'm bound to break something ![]() |
#24
|
|||
|
|||
![]()
I found a weak spot, the screws that hold the 320123-1. It takes the whole strange of the shock tower. I stripped the threads on both sides, and decided to make it more rigid. I added nuts on the inside of the plastic sides. No need to counter sunk as i did, low profile nuts will fit anyway.
|
#25
|
|||
|
|||
![]()
Or use 2mm longer screws to start with. Same with the front shock tower mounting screws need to be 2mm longer.
Quote:
|
#26
|
||||
|
||||
![]()
i have broken the carbon towers on my cat and cougar, carbon looks nice but breaks easily,. OK my driving is to blame for half of it, but i dont rate carbon for strenth.... at all...
__________________
XB4 & MORE , Team Xray, Team Gainsy Graphics, DPP Racing 2013 & 2014 OOPLE INVERNATIONAL BEER RACE RUNNER UP! FEEDBACK LINK =
|
#27
|
|||
|
|||
![]()
Same here. I stripped one side and then fitted longer screws - all OK now.
__________________
Tony Mulligan DESC410R, DEX410, DEX210, Cream Extreme (the dog's b******s) www.srcc.co.uk |
#28
|
||||
|
||||
![]() Quote:
![]()
__________________
A rc car is not just for christmas, it's for life
|
#29
|
||||
|
||||
![]()
I am working on my own ones, with a dremmel and some various materials, just some testing to do and may have a cheap supply made by yours truly!
![]()
__________________
XB4 & MORE , Team Xray, Team Gainsy Graphics, DPP Racing 2013 & 2014 OOPLE INVERNATIONAL BEER RACE RUNNER UP! FEEDBACK LINK =
|
#30
|
||||
|
||||
![]()
wel ive had 4 rear anti-squat blocks go the rear wish bone pins just tare out of them with not alot of impact done three at the mk gp this weekend not saying im the best driver out there and indoor racing is not that forgiveing but they are made from very flexible plastic.
and the HD ball caps pop off all the time on the 210 and the 410 v3 any one else had probs or is it just my bad driveing lol ![]() |
#31
|
||||
|
||||
![]()
Im still really confused how you did 3 martin! Me and Mark were both very confused.. I had a ball cup from the front pop off in Q1 and Q2. Think I will do the same to my old 410 and get Losi HD cups and HPi ball studs.. since doing that on my 410 had next to 0 issues.. As the Rango HD ones seem better than the old.. but not by much!
![]() |
#32
|
||||
|
||||
![]()
My steering turnbuckles kept popping of but rest seem fine. Anyone got part numbers for the losi cups and hpi ball studs?
|
#33
|
|||
|
|||
![]()
yep rear anti squat block ripped out ( not much impact) and cups pop off all the time, very soft plastic !!
|
#34
|
||||
|
||||
![]()
Losi HD ball cups with HPI-75115 and HPI-7116 ball studs
|
#35
|
||||
|
||||
![]()
I can't say about the 210, but since fitting the HD ball cups to my 410, I've only had them pop off once, and that was in a crash that would've took the entire front end off most cars.
__________________
Model Junction, Boughton Raceway. |
#36
|
||||
|
||||
![]()
still yet to pop a HD ball cup off on either the 210 or the 410.
![]() |
#37
|
|||
|
|||
![]()
Had a few big crashes indoors with mine, not broke a single thing.
It's certainly a strong car IMO. |
#38
|
|||
|
|||
![]()
Had loads of spares with me for the 210 at the MK GP expecting some breakages and had none. I have already put Losi ball cups on and Schumacher ball studs on the steering
![]()
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#39
|
||||
|
||||
![]()
Any idea on a part number or dimension for the Schumacher ball studs for the steering. Mine ball cup pops off the ball stud at the slightest tap.
__________________
SHRCCC Committee - Membership secretary & Treasurer. Amature racer, professional crasher. |
#40
|
||||
|
||||
![]()
Broke my steering rack last week during a awkward landing. replaced with Atomic Carbon version
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|