little ESC-position-mod on an X10

[Northy]

Mmmmmm, there wasn't that much wrong with the X10 spur gears to be fair, I did at least a whole season on one! It's all about the meshing IMHO.

G

[Alfonzo]

One more for the pot - I mounted my speedo directly on the chassis, but this required one of the servo ears to be cut, leaving the remaing ear and servo tape to do the job (which it has, no problems). Not totally ideal, but it does result in a very low C of G - which is nice.

Both me and my brother have had failed X10 spur gears, although we got a fair bit of racing done before failure, maybe half a season or so. FYI the X11 spur gear will rub on the 'Jesus Pin' rear brace unless you file / dremel some ally away.

Looking forward to hearing more about these 'high volume' shocks being tested..

[Alfonzo]

And whilst I'm here - I've just remembered, wasn't there a nicely executed mod from a French guy who mounted his servo 'end on' (i.e standing upright) which gave him loads of space to mount the speedo directly to the chassis? It looked good.

[footey]

yes but lewis owner of xtreme has also done it

[Lowie]

Originally Posted by Alfonzo

And whilst I'm here - I've just remembered, wasn't there a nicely executed mod from a French guy who mounted his servo 'end on' (i.e standing upright) which gave him loads of space to mount the speedo directly to the chassis? It looked good.

You mean like this?

[jeff jenkins]

i have also got my gtb mounted on the chassis and my servo is standing up.

[Alfonzo]

Yeah - that's the one Lowie. Just read your full post on the-pred, so I know the score with your setup now. Surprised you had thermal issues with the Mamba though.

Jeff - how you getting on with your Pred? Used it in anger yet?

[jeff jenkins]

Originally Posted by Alfonzo

Jeff - how you getting on with your Pred? Used it in anger yet?

what do you mean..lol

[footey]

have u actully raced it yet i think he means

[jeff jenkins]

nope waiting on parts. takes awhile to get them to me.

[ads0021]

I've got my low profile servo on its side. Loads of room!! Been running it like this for a few months now with no probs!

[darryl]

that is bloody neat what servo posts you using???

[mattym0310]

Its Lewis' car. I believe it's custom made. Team Xtreme were planning on releasing a conversion kit for this however, I havnt heard anything more of this so cannot confirm if it will happen

[Alfonzo]

Originally Posted by jeff jenkins

what do you mean..lol

lol - I meant have you used it yet, not are you angry yet!

[ads0021]

I used a short servo post mounted sideways onto the side of the tub on the outside and a cut down motor mount tube(ally one not the stainless one) on the inside. Then drill and counter sink the chassis where you want the servo to go. It does made a lot more space. The photo doesn't really show. I think you could probably get a normal size spectrum rec in. The other thing I've done is run the speedo wires out the bottom of the speedo and through the spine in the chassis.

[Chequered Flag Racing]

Originally Posted by ads0021

I've got my low profile servo on its side. Loads of room!! Been running it like this for a few months now with no probs!

have you opened up the chassis to lower the servo even further?

seen a picture somewere with that done but can't find it

mattym0310,
Its Lewis' car. I believe it's custom made. Team Xtreme were planning on releasing a conversion kit for this however, I havnt heard anything more of this so cannot confirm if it will happen

any news on a conversion kit ?

[jeff jenkins]

really there is no need for a conversion kit as it is simple to make the mounts your self. its a matter of drilling holes.. but it would be nice if there was so that way you have the correct mounts and not have to make them yourself.

[Lowie]

Originally Posted by Chequered Flag Racing

have you opened up the chassis to lower the servo even further?

seen a picture somewere with that done but can't find it
...

"open up the chassis"? What do you mean by this?
Any pictures of this?

about this servo-mount conversion-kit:
indeed very easy to make DIY, but I do know some guys that are VERY good in RC racing but can't screw a nut on a car without breaking some fingers
So such a kit can be very handy.

Thinking about it. If anyone wants some, I could make such a kit, by making some fitting special mounting-posts out of plexi. I'll try to make some and make some pictures, lol.

[Northy]

Originally Posted by jeff jenkins

really there is no need for a conversion kit as it is simple to make the mounts your self. its a matter of drilling holes.. but it would be nice if there was so that way you have the correct mounts and not have to make them yourself.

Now are you sure?

G

[Lee]

G, he used to be indecisive but now he`s not so sure