Kyosho RB6 thread

[jonathan may]

think they have sold it say out of stock on there site
but they do have one on ebay unless it was the same one ?

[gixxer]

One of the trader rules of listing on e bay is that it has to be in stock to list it

[jonathan may]

Is there any build tips out here before I start to build my rb6

[jonathan may]

Originally Posted by gixxer

One of the trader rules of listing on e bay is that it has to be in stock to list it

Lucky I did not order the rb6 off eBay it was out of stock

[sime46]

PBM still have a couple. Yours is on its way dude. I saw it go for packing yesterday.

[jonathan may]

Originally Posted by sime46

PBM still have a couple. Yours is on its way dude. I saw it go for packing yesterday.

yeah look forward to building it

[h0m3sy]

Does the Ultima SC gear diff fit the rb6?

[InsideLineModels]

Originally Posted by h0m3sy

Does the Ultima SC gear diff fit the rb6?

It certainly does

[h0m3sy]

Has anyone tried it?

[InsideLineModels]

Originally Posted by h0m3sy

Has anyone tried it?

I haven't yet, but David Poulter did on smooth high grip astro recently and said it worked well. I have one built... just haven't had the chance to try it yet.

[h0m3sy]

I think for the astro it would be good, as from my short time running the dex210, I found the gear diff to be better on astro and high grip surfaces, the ball diff when grip was low. Although saying that, I have yet to run my rb6 so I will reserve judgement till I do but it's good to have another option.

[billyboy9002]

New finnisher shell painted by the chef

[danmurphy]

Anyone know where I can find Christopher Krapps RB6 setup from the EOS race last weekend?

[stegger]

Originally Posted by danmurphy

Anyone know where I can find Christopher Krapps RB6 setup from the EOS race last weekend?

Nothing on here yet Dan ! http://www.petitrc.com/setup/kyosho/...UltimaRB6.html

[danmurphy]

Originally Posted by stegger

Nothing on here yet Dan ! http://www.petitrc.com/setup/kyosho/...UltimaRB6.html

Yea I already checked petitrc

[forbesy]

Hi all

I'm trying it install my electrics in my rb6 with Orion speedo at rear,receiver just behind slim servo at the front and the speedo wire is just a tad too short to reach the receiver thro the side pod.

Has anyone else had this problem. If so any ideas to get round it please

Cheers........

[billyboy9002]

Originally Posted by forbesy

Hi all

I'm trying it install my electrics in my rb6 with Orion speedo at rear,receiver just behind slim servo at the front and the speedo wire is just a tad too short to reach the receiver thro the side pod.

Has anyone else had this problem. If so any ideas to get round it please

Cheers........

I soldered a little bit more servo wire in the middle until I can get imull to lengthen the wire for me. And covered it in braiding with it run along the top on the side pod

[RudeTony]

Remember you can cut a new slot for exit of the wire out of the side slot at any point you wish - I did this to save the wire going all the way to the standard exit and then coming back again!!

[Chris-S]

Originally Posted by forbesy

Hi all

I'm trying it install my electrics in my rb6 with Orion speedo at rear,receiver just behind slim servo at the front and the speedo wire is just a tad too short to reach the receiver thro the side pod.

Has anyone else had this problem. If so any ideas to get round it please

Cheers........

I had the same issue, so widened up the entry and exits in the side guard, also cut the corner off the battery stop at the back so the wire exits the speedo and straight across into the sideguard, rather than having to go round a corner.

[h0m3sy]

We are READY....!