|
||
|
 |
|
||||||||||||||||||
|
#1
22-10-2009
|
|||
|
|||
b4 diff and drive shaft must be good condition
hi need some good drive shaft and a good diff that the cups on the outer are black not silver were the drive shaft go to the wheels my drive shaft dont fit in the rear caster right
Last edited by stampede vxlboy; 22-10-2009 at 09:22 PM. 
|
|
#2
22-10-2009
|
|||
|
|||
|
double post? you already have this in the wanted section?
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback
|
|
#3
22-10-2009
|
|||
|
|||
|
i know its worth a try
|
|
#4
22-10-2009
|
||||
|
||||
|
Quote:
__________________
|
|
#5
22-10-2009
|
|||
|
|||
|
sorry need some new ish drive shafts and a good diff is that better mate
as my cups of my diff are silver and looks worn and the drive shaft dont fit into the rear caster right were the wheels go
|
|
#6
22-10-2009
|
|||
|
|||
|
check your rear hub bearings then, they may be worn and very wobbly.
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback
|
|
#7
22-10-2009
|
|||
|
|||
|
i can move the rear caster with my hands and move the drive shafts
do the drive shaft fit into the reae hubs our do they look like they dont go in all the way i just priced all the parts new diff drive shaftdiff hubs diff ring and these other aparts 7677 ,9597,9755 £55 for the lot Last edited by stampede vxlboy; 23-10-2009 at 12:31 AM.
|
|
#8
22-10-2009
|
|||
|
|||
|
You can buy a complete and entire diff for the B4 now for less than £40 if it is that bad....
__________________
 ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
|
#9
22-10-2009
|
|||
|
|||
|
pm you about prices for my b4 parts
|
|
#10
23-10-2009
|
|||
|
|||
|
got most of the parts for my spare b4 that i am keeping and 1 forsale
|
|
#11
23-10-2009
|
|||
|
|||
|
So you want the factory team diff halves/outdrives as apposed to the normal ones... and you need some new hubs and bearings.. CVD bones...
i make that to be... £26.23... AS7668 AS7667 AS9597 AS9584
__________________
Team Losi Racing, Horizon Hobby TLR 22 5.0, TLR 22X-4, TLR 22-4, 22-4 2.0 Atomic Carbon S2, S44, Vega B4.1 Trader feedback: http://www.oople.com/forums/showthread.php?t=19374
|
|
#12
23-10-2009
|
|||
|
|||
|
parts 6581
7677 7667 7668 9584 9597 9688 wheels 9689 wheels 6588 and pins for the drive shaft i got told to buy all these parts do i need them all are the diff hubs on the diff silver and the drive shaft look like they dont fit in the rear huds right
|
|
#13
23-10-2009
|
|||
|
|||
|
If you could post some pics of what you mean when you say they dont fit that would be a great help?
Or what about... 290346741831
__________________
Team Losi Racing, Horizon Hobby TLR 22 5.0, TLR 22X-4, TLR 22-4, 22-4 2.0 Atomic Carbon S2, S44, Vega B4.1 Trader feedback: http://www.oople.com/forums/showthread.php?t=19374
|
|
#14
23-10-2009
|
|||
|
|||
|
give me 5 mins and i will put picture up
|
|
#15
23-10-2009
|
|||
|
|||
|
pictures of the drive shaft and diff and rear hubs,the drive shafts dont fit in the hubs right they stick out .and i can pull the shafts by hand
Last edited by stampede vxlboy; 31-10-2009 at 08:32 PM.
|
|
#16
23-10-2009
|
||||
|
||||
|
What is the problem? Looks fine to me.
Whoever sold you the car was kind enough to leave a set of MIP shiny bones on it. Rather nice of them. Make sure you have the silver spacer on the right way round with the conical side towards the bearing. You will not notice a difference between the factory team outputs and the regular team car ones! you might also need a couple of spacers on the inside of the hub too but nothing major. Can you drive the car at the moment or what is the problem exactly which you would need to toss that much cash at???
__________________
|
|
#17
23-10-2009
|
|||
|
|||
|
the problem is he has no idea how his car is meant to be built and is obsessed with buying unnecessary parts to fix things that aren't wrong!
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback
|
|
#18
23-10-2009
|
|||
|
|||
|
rear hubs are wearing away and the pins for the wheels are bent and the waster round side faces the outside toward the wheels and were can i get get alloy blue screw and nut for the shocks
|
|
#19
23-10-2009
|
|||
|
|||
|
what size are the bearing for the back wheels any parts number for blue alloy nuts and bolts for the shocks and bearing and spacer in the hubs not the round dis c were the pins sit for the wheels
Last edited by stampede vxlboy; 23-10-2009 at 09:58 PM.
|
|
#20
23-10-2009
|
||||
|
||||
|
Reread my post FFS!
Your wheel spacers are on the wrong way round! That is why your hubs are wearing and your drive pins are bending. Read the bloody manual! Do not attach the shocks with aluminium screws!!! There is a reason noone does this. Because it doesn't work and the screws bend and break. Run the car and don't glitz it up like a cheap hooker...
__________________
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Team Associated
Linear Mode
