|
|||||||||||||||
|
#21
|
||||
|
||||
|
I'd recommend the core's, very good lipo's for the money !
I'd also consider the Intellects at £50
__________________
Ben Marzec LRP Shark FT Associated B44 - LRP Powered Tamiya 416WE - Protoform LTC-R |
|
#22
|
||||
|
||||
|
Agreed, and if you take to much off some lipo hard cases, you will have a hole in the case before you get the hump level to the bottom of the rest of the lipo case. Especially the intellects with carbon look case.
__________________
Rango St Ives |
|
#23
|
||||
|
||||
|
OK! Check this out. The SMC 4700 40c Lipos have humps on the base, but the can be used upside down because there are tube connectors on each side. Genius. Will work no problem in the SX, and they are 40c
![]() http://www.rc-mushroom.com/product_i...ducts_id=17823
__________________
Rango St Ives |
|
#24
|
|||
|
|||
|
Quote:
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
|
#25
|
||||
|
||||
|
Indeed I do want BRCA legal as at some point I will be doing an event. Bit late for this year though
![]() Any plans for the vampire racing to have the connectors on the other side too? |
|
#26
|
|||
|
|||
|
They are not allowed to change the spec once it is submitted for BRCA/EFRA approval, if they did they would be illegal. So in short, no not at present
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
|
#27
|
||||
|
||||
|
The Gp 5300 30c lipos have corally tubes on both side
Turn them up side down
|
|
#28
|
||||
|
||||
|
I didn't know intellect did 5000's with 40C. Perfect for tourers
![]() The only problem with the LRP's is that there £99.99 RRP but I suppose you pay for quality. The Orion 3800 are still £89.99 and they're only 30C but the cells are Kokam. You pay for quality
__________________
Ben Marzec LRP Shark FT Associated B44 - LRP Powered Tamiya 416WE - Protoform LTC-R |
|
#29
|
||||
|
||||
|
Just weighed some GP 4000's and some 5000's and a pack of Orion 3800
GP 4000 : 232g GP 5000 : 272g Orion 3800 : 231g Orion's were only 1g lighter than the GP4000's but they look so much smaller and look look less bulky
__________________
Ben Marzec LRP Shark FT Associated B44 - LRP Powered Tamiya 416WE - Protoform LTC-R |
|
#30
|
||||
|
||||
|
Interesting.. The weight factor is rather critical in my XXCR, but not sure about the Cat SX (haven't run it yet)
|
|
#31
|
|||
|
|||
|
Quote:
Orion may be Kokam's but the LRP's are not exactly cheap and nasty tat inside, they are excellent quality too with more capacity and power to boot.
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
|
#32
|
||||
|
||||
|
Yeah I agree, id rather have the LRP
__________________
Ben Marzec LRP Shark FT Associated B44 - LRP Powered Tamiya 416WE - Protoform LTC-R |
|
#33
|
||||
|
||||
|
I agree as well The Gp's are good for the price
|
|
#34
|
||||
|
||||
|
Yep I run the GP4000 35c's in my 416 WE and I think they're brilliant
__________________
Ben Marzec LRP Shark FT Associated B44 - LRP Powered Tamiya 416WE - Protoform LTC-R |
|
#35
|
||||
|
||||
|
What LIPOs did you get in the end and how many have moved to the new stiffer chassis?
|
|
#36
|
||||
|
||||
|
I got the GP 4300 35c Lipos from Hong Kong in the end
Only £40 with P&P Had to take abit of the humps on the lipos to make them fit under the battery bar, but they fit fine Used the same chassis |
|
#37
|
||||
|
||||
|
Don't want to dremel the batteries etc. So it sounds like a no go.
|
|
#38
|
||||
|
||||
|
dont dremmel the batterys dremmel the chassis,im pretty sure if u dremmel them there no longer legal,
__________________
Mattys the driver,my names carl
|
|
#39
|
||||
|
||||
|
My thoughts exactly, whats the point in spending all that money and then becoming illegal..
|
|
#40
|
||||
|
||||
|
http://westlondonmodels.com/product2...P-5000-Car-PR/
EFRA legal - I belive also BRCA legal. It's my choice no.1
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。| | Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts | |
![]() |
| Thread Tools | |
| Display Modes | |
|
|