What's needed for a Stick Lipo Conversion

[dayxwalker]

I have just got a X11 and I am thinking of converting it to stick lipo ! I have read the post on it but I need to know exactly what bits I need.

My electrics are as below
GTB esc
Acoms 2.4ghz reciever (tiny)
Full size servo (jr9002z)

Is there no way of getting a full size servo in ? Don't have the cash for a low profile at the moment.
I need to swap the linkages to the otherside for the servo but are they compatable to either side ?
I will have to shorten the servo rod (long one) then tap the end ?

[Bungleaio]

I'm about to try and do this on my car.

It'll be tight getting your electrics in as the gtb takes up a fair bit of space on its own. The steering links can be turned upside down and used on the opposite sides the only problem I can see is the countersunk screws that are on one end of them, I'm not sure how this will work now.

As for the rod, you can cut the existing one down and rethread it or you can buy a length of M3 threaded rod and sut that to whatever lenght you need, this is what I have done.

[blitzboy]

dayxwalker when you reverse the steering arm pieces you need to dremmel off the lump s and the put a nut on to retain it underneath , as for having a full size servo you could always lay it down and then shorten and bend the steering rod to siut it as for your reciever and gtb you d have to see where it will go after that first thing i would do is try and place the servo as far forward as possible then look at where to mount your reciever and speedo after

[turbo_brick]

If you want I'll have a look see what I can come up with. I've got a old chassis somewhere.

Peter

p.s. sorry I haven't pm'd back Tim just been busy all week at the track.

[KevLee]

Originally Posted by dayxwalker

I have just got a X11 and I am thinking of converting it to stick lipo ! I have read the post on it but I need to know exactly what bits I need.

My electrics are as below
GTB esc
Acoms 2.4ghz reciever (tiny)
Full size servo (jr9002z)

Is there no way of getting a full size servo in ? Don't have the cash for a low profile at the moment.
I need to swap the linkages to the otherside for the servo but are they compatable to either side ?
I will have to shorten the servo rod (long one) then tap the end ?

I have a short stack servo but mounted on its side and there is no reason why a full size servo wouldn't fit like that. I have the reciever on the chassis between the servo and prop and the speedo upfront. You could mount the reciever on top of the servo, or if you speedo is too big for the space upfront that could go on the servo and put the reciever up front?

The steering links do need to be countersunk on the other side so that the screw heads don't catch on the chassis.

I'm using the original servo rod but with a little bit taken off.

I can post a picture if that helps as i've changed it around a bit recently?

[Bungleaio]

Originally Posted by KevLee

The steering links do need to be countersunk on the other side so that the screw heads don't catch on the chassis.

Does this not leave very little material on the arms?

[dayxwalker]

Thanks everyone !
Pete that broken chassi would be good to play with so I don't end up drilling loads of holes in the process !
I am racing on Tuesday so to soon to take it to bits but I will start on Wednesday !
I like the idea of just getting threaded bar saves buying a tap !
I will post some pictures as I go ! Don't think I have seen a full size servo in a stick pred ? I don't want anything sticking out of the shell tho !

[dayxwalker]

One other thing I just hope it handles ok with sticks ! I can always go back to saddle !

[turbo_brick]

I've just been messing about with that broken chassis, seems I can get everything into it, need the size of your reciever though.

I'll show you tomorrow if i remember.

Peter