Team Orion r10 setups

[pizzaman]

Has any one got a good settings starting point using a ballistic 6.5 motor
On 7.4v lipo

[cornishboy176]

2wd/4wd?

I ran a 6.5 in my Centro with punch control on 2 and drag brake on 10% all other settings turned off,it was still too quick and I have now gone down to an 8.5 and it's alot smoother,it also depends on the size of track too

[Crash]

I've been using a setup from one of the Orion drivers to pretty good effect with my 6.5 and R10. My local track does have quite a long straight though and my centro is geared 24/78.

Drag brake 10%
Punch Mode Level 5
Max Brake 75%
Initial Brake drag brake
Neutral range 6%
Boost Timing 10 degrees
Boost Start 5000rpm
Turbo Timing 15 degrees
Slope Rate Fastest
Turbo delay 0.3s

[RudeTony]

Originally Posted by pizzaman

Has any one got a good settings starting point using a ballistic 6.5 motor
On 7.4v lipo

What level of racing are you at?

Originally Posted by Crash

I've been using a setup from one of the Orion drivers to pretty good effect with my 6.5 and R10. My local track does have quite a long straight though and my centro is geared 24/78.

Drag brake 10%
Punch Mode Level 5
Max Brake 75%
Initial Brake drag brake
Neutral range 6%
Boost Timing 10 degrees
Boost Start 5000rpm
Turbo Timing 15 degrees
Slope Rate Fastest
Turbo delay 0.3s

WOW!
Thats a very aggressive set up..you sure you have that right?

[Crash]

Originally Posted by RudeTony

WOW!
Thats a very aggressive set up..you sure you have that right?

I hope so Tony - it's what you gave me as a starting point for TORCH!!

I'll happily take further suggestions though

[RudeTony]

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

[Crash]

Originally Posted by RudeTony

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

Consider me re-educated
I'll send you an email shortly.

[OneKiwi]

How about setting for in a 410?
Thanks

[Dudders]

Originally Posted by RudeTony

LMAO - 7.5 motor, not 6.5!
With a 6.5
change to

Punch = 3
Timing = 10
Turbo = 10
Slope = 18
Delay = 0.4

If you have a set up from me its wrong and I need to know

What would you do with a 10.5 at SHRCCC Uncle T?

[RudeTony]

Hi Neil

At SHRCC I run an Orion (obviously lol) 7.5 in 2wd with the following settings

Punch = 7
Timing = 6
Turbo = 8
Slope = 12
Delay = 0.3

I belive you have recently extrended the track and I haven't had an oppotunity to race on it yet.....this setting was for your original track.
Punch was turned a little more than normal as wanted the punch between the shorter corners.The turbo was turned down from normal set up as it generated too much and was close to wheelies on the high grip straight.
I did though bring in the turbo earlier to get her going quicker
I hope it all makes sense.......and helps

[Matt Butcher]

As always very helpful tony! out of interest which software do you run?