|
||
|
 |
|
||||||||||||||||||
|
#1
07-03-2010
|
||||
|
||||
B4 Rear Drive pin a touch short?
Noticed where the drive/roll pin sits in the hub of my B4 rear wheels that they are getting a little worn rather quick, the pins seem to be a little shorter than they might be which could be a factor?
Anyone else had this, if so, any idea of a good solution, perhaps some slightly longer pins?
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk 
|
|
#2
10-03-2010
|
||||
|
||||
|
Just me?
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk
|
|
#3
10-03-2010
|
||||
|
||||
|
I'm not sure what you mean...
__________________
 CML Distribution - Distributors of Quality Radio Control Models & RC Hobby Products
|
|
#4
10-03-2010
|
|||
|
|||
|
My car has some solid pins which are the right size for the driveshaft hole, and the right length for the wheel slot. These were on the car when I got it. The only problem is they fall out when you take the wheels off. The losi split pins used in the XX4 etc may fit, i'm sure they are longer than the associated ones. Might have to try that one myself!!
|
|
#5
10-03-2010
|
||||
|
||||
|
Erm...the drive shaft comes through the hub bearings and there is then a pin, referred to as a 'roll pin' i believe that goes through a hole in the drive shaft. This pin then engages in the wheel to provide the drive transfer to the wheel?
Might have just answered my own question actually: http://www.sosidge.com/?p=418 3/4 the way down this guy mentions the same problem and has replaced them with 'nortech' drive pins, who are Nortech?
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk
|
|
#7
10-03-2010
|
||||
|
||||
|
Hmmm..anyone got any info on the Losi split pins?
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk
|
|
#9
11-03-2010
|
||||
|
||||
|
Hmmm...sounds like Nortech might be the answer, anyone got a weblink to them? Tried Google without much success?
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk
|
|
#10
12-03-2010
|
||||
|
||||
|
Quote:
 Check out Northy, he's a member here. The link to his shop is in his sig Paul
|
|
#11
12-03-2010
|
||||
|
||||
|
Yarp, found it under nortech racing...DOH...placed an order for the solid CAT rear drive pins to use...
__________________
Losi Muggy-R (Spek, SH .28, 48T Spur, Steering mod, ACE) Losi 8Te (Castle MMM, 2200kv, Hyperion 6500mah 4s 35C Lipo, RC-M motor mount, Losi battery/radio tray) Maverick Atom XB 1/18 (Spek) Associated B4RS (Spek, Castle MM/5700KV, Lipo) Associated SC10 (Spek, Novak/8.5 Turnigy, Lipo) www.ddgraphics.co.uk
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Team Associated
Linear Mode
