|
#1
|
||||
|
||||
![]()
Got a problem with the Vectra C 1.9 CDTi, fumes in the cabin. I'm almost certain it's not the exhaust as that's had a new flexy joint. Been told on a Vectra forum that it could be leaking from the manifold where the swirl valves are, is this likely?
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#2
|
||||
|
||||
![]()
ill ask my mate but
if its running with the bonnet up, can you hear a blowing? or see smoke?, on fords we get injectors blowing combustion pressure back past their seals, in which case its a new fire washer ( copper washer at end) and refit
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#3
|
||||
|
||||
![]()
I can't really see anything Mark. It is wet again round the injector now though after cleaning it off yesterday.
I don't mind a few £ for a new seal or the like but bollox to £1k for a new manifold ![]() G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#4
|
||||
|
||||
![]()
mate says check pollen filter and round egr too ( egr will be near exhasut and a pipe to inlet some where.
wet as in clear or sooty? could easy be injectors blowing back, they been out at all?
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#5
|
||||
|
||||
![]()
Check pollen filter for what Mark? I looked arounf the ERG valve, couldn't see anything. Looked like all the pipes were solid.
It's wet around injector, diesel, but there is also a lot of brown crud (sort of baked on) that I couldn't clean off. G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#6
|
||||
|
||||
![]()
pollen filter not seated right letting fumes in, id say its your injector seal, needs pulling out, cleaning out ( that brown crud) and refitting with a new washer from vauxhall
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#7
|
||||
|
||||
![]()
Cheap fix?
VX dealers job? ![]() G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#8
|
||||
|
||||
![]()
says easy job, unbolts and pull out, just be carefull of tip
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#9
|
||||
|
||||
![]()
Can I get the seal or does he think I should get VX to do it really? I hate this car
![]() G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#10
|
||||
|
||||
![]()
you should be able to get seal, ask for a qoute to do work. its simple for a good tech
you need this out and renew the copper bit at the bottom, (clean all the old crap out the hole too) ![]()
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#11
|
||||
|
||||
![]()
Stop smoking dope in ya car.
__________________
I may not have the key to success, but I know how to pick the lock on the door.
|
![]() |
Thread Tools | |
Display Modes | |
|
|