Go Back   oOple.com Forums > General > Electrics

Reply
 
Thread Tools Display Modes
  #1  
Old 20-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default Is my brushless motor broken? Please help

Just took out the Xray for a little bash, running the 6.5t Fusion Exceed Motor and ESC combo.
After the run i revved up the car and heard a little pop, then my Motor will not turn anymore.

The motor nor ESC where hot, they were only warm.

It makes a whining noise under power, thats about it.

What can i do? I only bought it a couple of weeks ago.
Reply With Quote
  #2  
Old 20-08-2011
jamie 6.5t's Avatar
jamie 6.5t jamie 6.5t is offline
Member
 
Join Date: Jul 2011
Location: lowdham
Posts: 247
Default hi

hi there have you tried turning the shaft with your fingers if it dont turn ide advise you to take the back of it may be something simple like one of your bearings have moved or poped out if so just pop it back in or buy a new set ov bearings if they are broke but if you dont feel confident taking it to peaces then take it to the shop you got it from and demand a refund :P
Reply With Quote
  #3  
Old 20-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

Thanks for your response, im panicking as i cannot afford to replace this combo it cost me £120!


Ok i got it from Modelsportuk, but i might contact Logic RC to see what they say too.

Will i void my warranty (if i even have one) if i open it up?

When i turn the motor, it feels different to before, but it does turn by hand.
Reply With Quote
  #4  
Old 20-08-2011
jamie 6.5t's Avatar
jamie 6.5t jamie 6.5t is offline
Member
 
Join Date: Jul 2011
Location: lowdham
Posts: 247
Default hi

yeh i had brought the same combo but got it for 110 got discount lol but after a week ov running i spotted a 3800kv motor from castle creations and swapped the motor and it shifts like no tomorow now bearing mind ive got it in a road car lol its hitting the 70mph mark easyly i recon
Reply With Quote
  #5  
Old 20-08-2011
Naushad Naushad is offline
Mad Member
 
Join Date: Dec 2010
Location: Cardiff, Wales
Posts: 1,430
Default hi

Don't open the motor or take it to pieces! Likely to void warranty. Especially if you've bought from new.

Is your sensor cable plugged in properly?

Do you sense an odd smell with the ESC? If so you may have blown a FET in the ESC.

I would return back to modelsport....probably easiest ans safest thing to do.

Regards

Naushad
Reply With Quote
  #6  
Old 20-08-2011
jamie 6.5t's Avatar
jamie 6.5t jamie 6.5t is offline
Member
 
Join Date: Jul 2011
Location: lowdham
Posts: 247
Default hi

actually yeh take it back and if u cant get a new one take it to ur club and get someone to sort it for u
Reply With Quote
  #7  
Old 20-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

No smells, everything seemed normal in terms of appearance, smell and temperature just after the little pop noise.

Servo is working fine, i think ESC is fine, ill connect it to my brushed motor to check.

Sensor cable is plugged, when its unplugged i get nothing at all, no noise. Plugged in i get a noise.

When i turn the motor it feels like something is almost like grinding, but not very much, enough too feel it and still turn the motor.

I dont have a club, i just bash lol
Reply With Quote
  #8  
Old 20-08-2011
Naushad Naushad is offline
Mad Member
 
Join Date: Dec 2010
Location: Cardiff, Wales
Posts: 1,430
Default

Im not quite sure what you are feeling with the motor is quite normal..

You could check the esc with your brushed motor but bear in mind the circuit connections are different!

Don't panic!

Just take back to the shop so they can inspect matters.
Reply With Quote
  #9  
Old 23-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

I was advised by MSUk to send the motor to them with a letter, i wrote:


I have recently purchased the “Fusion Exceed Pro Brushless Combo - 6.5T” from yourselves at the start of July. After only a couple of runs on the weekends it seems to have developed a fault on 21/08/11. Towards the end of my run the motor seemed to stop responding. I checked the temperatures, both the Motor and ESC were only warm; I could hold them for over 5 seconds.
After taking my car apart I found that the motor wouldn’t spin under throttle or reverse, it only makes a whine sound. I could turn the motor by hand but it doesn’t feel normal.
I was advised over the phone to return the Motor to yourselves so you could take a look at it for me and hopefully arrange an exchange, the motor and ESC are in near new condition physically.
Reply With Quote
  #10  
Old 24-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

ModelsportUK just contacted me to say they have received the motor and are sending it to Logic RC for investigation.
Cost me £6 to send it back, i hope its worth the trouble.
Reply With Quote
  #11  
Old 26-08-2011
Big paul Big paul is offline
Member
 
Join Date: Nov 2010
Posts: 190
Default

Just for future ref never rev a brushless motor with no lode on it, ie off the ground .
Reply With Quote
  #12  
Old 26-08-2011
Muzzie's Avatar
Muzzie Muzzie is offline
Senior Member
 
Join Date: May 2011
Location: Mansfield
Posts: 326
Default

I've also just posted mine back to Model Sport as its just stop working. I've asked they inspect the ESC & Motor to find the reason for the fault and repair / replace the items under warranty. Let me know how you get on and I'll do the same. Hope it's not going to take to long as I'm out of action
Reply With Quote
  #13  
Old 26-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

Muzzie, how long have you had yours for? What car, what gear ratio?
Reply With Quote
  #14  
Old 26-08-2011
Dudders's Avatar
Dudders Dudders is offline
SHRCCC Legend
 
Join Date: Apr 2009
Posts: 4,317
Default

Quote:
Originally Posted by Big paul View Post
Just for future ref never rev a brushless motor with no lode on it, ie off the ground .
Why?
__________________
Vega RB6 - Orion - Apex Models - JE Models - Cable ties
Reply With Quote
  #15  
Old 26-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

I didnt rev it off the ground, i revved it into my driveway ; )

Also i only hear that revving the BL motor without connected to the spur is bad.
Reply With Quote
  #16  
Old 26-08-2011
bodgit's Avatar
bodgit bodgit is offline
*SuPeRsTaR mEmBeR*
 
Join Date: Feb 2008
Location: North Wales
Posts: 2,363
Default

Quote:
Originally Posted by Dudders View Post
Why?
http://www.bing.com/search?q=free+re...sk=&x=108&y=13
Reply With Quote
  #17  
Old 27-08-2011
D20MCK's Avatar
D20MCK D20MCK is offline
Senior Member
 
Join Date: Jun 2008
Location: Grangemouth, Scotland
Posts: 423
Send a message via MSN to D20MCK
Default

Quote:
Originally Posted by Dudders View Post
Why?


http://www.teamnovak.com/tech_info/f...g_warning.html
Reply With Quote
  #18  
Old 27-08-2011
Muzzie's Avatar
Muzzie Muzzie is offline
Senior Member
 
Join Date: May 2011
Location: Mansfield
Posts: 326
Default

I've had the set up for around 8 month and it's just been used for general bashing / practicing. I'm running a CAT SX and I went to my first race meet 2 weeks ago. All was well but in the final the thermal cut out kick in and then this week in the first race it just gave up ...

With regards gearing I'm still really GREEN and it all seams a dark art , but I took a setup off the Schumacher web site:

Pinion 22t
23t Layshaft
33t Idler

Could this of caused the fault???
Reply With Quote
  #19  
Old 30-08-2011
jasjeet jasjeet is offline
Member
 
Join Date: Apr 2011
Location: London, Slough
Posts: 102
Default

Havent had anything from MSUK since 24th August when they said they are sending it to the supplier.
Hopefully i get something soon.
Reply With Quote
  #20  
Old 30-08-2011
Muzzie's Avatar
Muzzie Muzzie is offline
Senior Member
 
Join Date: May 2011
Location: Mansfield
Posts: 326
Default

Same with me, 7-14days I've been told
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com