Go Back   oOple.com Forums > Car Talk > KYOSHO

Reply
 
Thread Tools Display Modes
  #1  
Old 17-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default shock ends

Hi,
could someone tell me are the LA43 shock ends to give more droop at the front a option part..or are they in the kit???

thank you,

regards simon
Reply With Quote
  #2  
Old 19-06-2006
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

they are an option part ( which is nice n cheap) to give more droop you will have to remove 3mm off of its lenth to equal the standard rear droop
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #3  
Old 19-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

Hi Nathan,
thanks for that.....any other little tricks or tips i should know!!

Cheers simon
Reply With Quote
  #4  
Old 19-06-2006
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

tips wise not a lot only to get a few alloy parts to strenthen the front end tungsten carbide or ceramic diff balls and boil ya plastics to make them a little more flexible, the setups i run are posted in this section but run a diff and oneway layshaft in the front as it makes the car a little easier to drive i have spent a lot of time trying to get a good no roll bar set up for the car but 9 times out of 10 go back to the stotfold set up as it is a safe bet on 90% of tracks. if you have any build questions or setup help needed please ask

nathan
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #5  
Old 19-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

Hi nathan,

what front end parts do you replace in alloy??....and why change the diff balls..are the standard ones dodgy!!??

I bought my zx5 as a new build..it has titanium turnbuckles,screws,atomic carbon shock towers,and centre deck,alloy front d piece.shim removed from the front d piece,10 degree front hubs,40 wt oil in the front yellow springs...30 wt oil in the rear blue springs.....does this seem ok??

cheers simon.
Reply With Quote
  #6  
Old 20-06-2006
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

hi simon,
the front end parts are the shock mount mount,youve allready got the carbon front shock mount use the kit one with it as a sandwhich this makes the front very strong,the diff balls theyll be allright for a meeting maybe 2,but deffo needs replacing,as for setups have a look at the stotfold setup you wont go far wrong just change one way diff for one way layshft and diff,

trekkker(stu)
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #7  
Old 20-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

Hi stu,
Thanks you..just a couple of things!!..on the stotfold set up it says front knuckle opposite?..and rear hub 0 degree..is the rear hub 0 degree as standard or is this an option.

Cheers simon.
Reply With Quote
  #8  
Old 20-06-2006
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

hi simon,
the rear hub is zero degrees as standard,well spotted i think it should be standard,

trekkker stu
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #9  
Old 20-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

And what does front knuckle opposite mean?????

Cheers simon
Reply With Quote
  #10  
Old 20-06-2006
simon simon is offline
Senior Member
 
Join Date: May 2006
Posts: 753
Default

Hi stu,

have you got a number i can call you on as i have a few other questions!!!..trying to get it sorted for the next 4wd meet.


Cheers simon.
Reply With Quote
  #11  
Old 26-08-2006
Hobie's Avatar
Hobie Hobie is offline
Member
 
Join Date: Aug 2006
Location: Hong-Kong
Posts: 37
Default

Quote:
Originally Posted by niggs98
tips wise not a lot only to get a few alloy parts to strenthen the front end tungsten carbide or ceramic diff balls and boil ya plastics to make them a little more flexible, the setups i run are posted in this section but run a diff and oneway layshaft in the front as it makes the car a little easier to drive i have spent a lot of time trying to get a good no roll bar set up for the car but 9 times out of 10 go back to the stotfold set up as it is a safe bet on 90% of tracks. if you have any build questions or setup help needed please ask

nathan
Hi Nathan,

After two months, is Stotfold set-up still for you the safest set-up for a 'common' ZX5 driver as me ? Furthermore, I took your Stotbold set-up sheet in the 'set-up thread', is it still relevant ?
Another short question. Which type of grease should I put in the diff cases : asso white or black or another one...?
thanks in advance for your help.

Bruno

Last edited by Hobie; 26-08-2006 at 09:36 AM.
Reply With Quote
  #12  
Old 28-08-2006
niggs98's Avatar
niggs98 niggs98 is offline
Woop Woop Member
 
Join Date: Oct 2005
Location: birchington kent
Posts: 1,682
Default

hi there bruno, for set ups it depends on the surface you are running on but recently we have changed the setup on the car to the oswestry setup which seems to make the cars transiton to diferent surfaces alot easier. some people cant get up the whole setup on here so if you sufer the same fate then start with the batley set up as this is nearly the same. you will find that the car comes out of corners alot easier but will still get in the same as usual. on my diffs i use associated clear but on the gears iv just started using a tamiya teflon grease after someone recommended it to me so will report on that after a few more meetings
__________________
Nathan Ralls HPI, Custom Blitz, www.piraterc.com mr-o foams

woop woop racing officialy keeping team toe out inline
Reply With Quote
  #13  
Old 28-08-2006
Hobie's Avatar
Hobie Hobie is offline
Member
 
Join Date: Aug 2006
Location: Hong-Kong
Posts: 37
Default

Thanks Nathan for your help. I will try and keep you informed. Another short question. In most of your set-up sheets front spring are softer than rear ones which seems to me not so common (normally on other cars, it is the opposite). What is the reason of this ? Due to the pack configuration ?

Bruno (ZX5 happy driver)
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 06:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com