|
||
|
 |
|
||||||||||||||||||
|
#1
20-10-2007
|
||||
|
||||
7.2v servo's
Can someon please link me to the right type of choke you need for 7.2v servo's. Normally i dont run one in my 2wd as its only a cheap KO servo so didnt see the point as it worked fine without one but with my new 2123 coming for my xx4 its a bit more exspensive so i want one for both of them.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! 
|
|
#2
21-10-2007
|
||||
|
||||
|
My 2123 came with one in the kit...
__________________
|
|
#4
21-10-2007
|
||||
|
||||
|
You should always run a FET choke when using a 7.2v servo regardless of car. It helps prevent voltage spikes running to the servo which can cause glitching/interference.
M. 
|
|
#6
21-10-2007
|
||||
|
||||
|
http://www.mtroniks.net/mtroniks_pro...bCategoryID=36
any shop with an mtroniks account, £1.35 ps or else what ash!
__________________
AC S4-LRP SPHERE TC-KO2123-NOVAK 5.5L B4FT-NOSRAM EVO-KO2123-SPASHETT 10x2 http://s343.photobucket.com/albums/o...-rugby-new.gif
|
|
#7
21-10-2007
|
|||
|
|||
|
|
|
#9
23-10-2007
|
||||
|
||||
|
I got the servo this orning its ace and the choke was included so im tkaing it doesnt not have to go any particular way.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves!
|
|
#10
23-10-2007
|
||||
|
||||
|
No Ash, a choke (inductor) is not polarity sensative - which means you can connect it either way round.
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing 
|
|
#11
23-10-2007
|
|||
|
|||
|
You can get them from electronics shops for pennies, not sure of the exact specs you want though. 4.7mH rings a bell for some reason...
 G?
|
|
#12
23-10-2007
|
||||
|
||||
|
Yeh, they're 4.7, 47 or 470 uH, can't remember!
 G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing
|
|
#13
23-10-2007
|
||||
|
||||
|
Also is it ok to use this little plug thats on the servo ir is it best to just solder it on as it looks alittle loose. May come apart mid race.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves!
|
|
#15
23-10-2007
|
||||
|
||||
|
I use the little connector with some heatshrink over it to stop it coming apart.
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing
|
|
#16
23-10-2007
|
||||
|
||||
|
OK i think ill just solder it it saves on length as the length on the servo alone is long enough to reach from the servo to the speedo so ill just wire it dirrect.
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves!
|
|
#17
23-10-2007
|
||||
|
||||
|
Got it in and done all the wiring put the choke between the servo and the plug then just soldered the plug onto the speedo blue wire and joined them up ace
And look at the blink of the nortec blue washers and nortec screws there ace!!!!  Again another crap picture from my webcam but it looks ace well chuffed now ive gathered the reciever wire up to so its in sorta nice tidy pile thing lol A 
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves!
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
