|
||
|
 |
|
||||||||||||||||||
|
#1
11-09-2010
|
|||
|
|||
LRP Blast - brushless
Managed to pick up a cheap blast truck with the intention of replacing my rustler as main bashing vehicle.
So for starters, transplant everything into the blast, with a 3s lipo:    initial run was promissing, a lot of flexing from different components but overall very stable. There was a lot of play in the rear hubs, they also used a small 5x8 bearing, I transplaned the rustler rear hub into the blast, had to mill a tiny bit off each side.  and make some hinge pins, E clip on one end, cut a thread on the other for a lock nut, larger 5 x 10 bearings on the left.   When the servo saver is tightened right up the bearing can fall out the bottom! so I made a tiny alloy collar to hold the bearing in place  on the top of the rack, trimmed the plastic and secred the screw with a nut instead.  Now the chassis, sent off to the good people at fibrelyte, I wanted the top deck a bit thinner and the battery strap a lot wider for the lipo. 
|
|
#2
11-09-2010
|
|||
|
|||
|
All the screws in the standard car are pretty naff, the hex rounds easily so I changed them all for stainless hex heads
 machined a piece of delrin as a lipo tray to stop any movement.  installed, nice!   drilled 2 more holes to screw the speedo down  just waiting on some shims to re-shim the diff and some proper wheel hex's then I can give it a blast! 
|
|
#3
11-09-2010
|
||||
|
||||
|
Mate that is an impressive mod. Keep the pics coming.
|
|
#4
12-09-2010
|
||||
|
||||
|
Fantastic.
Wish i could have the machines to be able to do such things.
__________________
 Chris Brown.rb5, Mission, F109, F103, F104v2 titanium, F104v2 black, 2 FF01s, FF03, TA02, TA04ss, TA04r, TA05, TT01, TL01, trf 415, M01, M02, 2 M03s, M04, M05, M06, XEVO, DB01, T2R Pro, TC3, b3, SC10, RC10 R5, E Revo, MR4 TC, MR4 TC worlds, MR4 BC SP, Ym34, xxx-t, Mad Rat, Predator DTM, Holiday Buggy (red), H.B (blue), dt03.
|
|
#5
24-09-2010
|
||||
|
||||
|
Very nice work! I like it!
Where did you get that piece of delrin? I'm searching for that stuff. Grts,
|
|
#6
24-09-2010
|
|||
|
|||
|
Very nice work indeed. Looking forward to hearing how well it goes.
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff!
|
|
#8
10-10-2010
|
|||
|
|||
|
this is very nice just like the rustler you did drop me a pm about this truggy i would like one
|
|
#9
14-10-2010
|
|||
|
|||
|
how much would it cost to have a car like this its a beast
|
|
#10
28-10-2010
|
||||
|
||||
|
Blast
Going to give the little beasty a try again this christmas So with that in mind I have spoken to fibre-lyte and asked them to make me a chassis but with holes for the lrp battery packs and a thinner batt strap. Also a hole for the spur gear resess. Then hopefully when all the LRP carbon towers and rear driveshafts hex's and other bits come It will get blinged up ready to roll again.
__________________
 Weight loss only requires one frame of mind " DO OR DO NOT ! THERE IS NO TRY "
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
