Go Back   oOple.com Forums > General > Electrics

Reply
 
Thread Tools Display Modes
  #1  
Old 22-02-2009
toooldskool toooldskool is offline
Senior Member
 
Join Date: Jan 2008
Posts: 333
Default Brushless and 40 MHz

I understand that you can only use 2.4 Radios with Novak Brushless systems . Is this the case for other manufacturers as I currently still use a sanwa gemini system
Reply With Quote
  #2  
Old 22-02-2009
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

where did you here that to?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
  #3  
Old 22-02-2009
rc_penguin's Avatar
rc_penguin rc_penguin is offline
Senior Member
 
Join Date: Apr 2008
Location: Whitstable, Kent
Posts: 428
Default

I use a novak brushless system with a sanwa gemini? never had problems with interferance?
__________________
Will Johnson
Reply With Quote
  #4  
Old 22-02-2009
toooldskool toooldskool is offline
Senior Member
 
Join Date: Jan 2008
Posts: 333
Default

Quote:
Originally Posted by DCM View Post
where did you here that to?
A mate is running a Novak brushless Losi 1/8 and he had problems and was advised by Novak that the systems were designed to be used in conjunction with 2.4.
If this is not the case and I could use my sanwa system that would be very good news.
Reply With Quote
  #5  
Old 22-02-2009
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

I know the Novak HV systems can cause problems with AM radios, my E-Revo was basically unusable with the stock AM radio, no problem with 40MHz FM though.
Reply With Quote
  #6  
Old 22-02-2009
peetbee's Avatar
peetbee peetbee is offline
*SuPeRsTaR mEmBeR*
 
Join Date: Aug 2007
Location: www.caldicotrcracers.co.uk
Posts: 4,013
Default

Novak do 2 versions of the GTB, the spread spectrum version is intended for 2.4g systems only I believe.
I have the non spectrum version and it was fine on 40mhz, still fine now I have 2.4g!
Reply With Quote
  #7  
Old 22-02-2009
Cooper's Avatar
Cooper Cooper is offline
oOple Contributor
 
Join Date: Jan 2006
Location: Ghent, Belgium
Posts: 1,731
Default

Me and some other have had problems with Novak and 40mhz

Now the system is installed in my 1:12th scale and I don't have it any more. (shorter range I think).
__________________
www.rc-offroad.be
Never argue with a stupid man. He will drag you down to his level and beat you because of his experience.
Reply With Quote
  #8  
Old 23-02-2009
Welshy40's Avatar
Welshy40 Welshy40 is offline
Spends too long on oOple ...
 
Join Date: Sep 2006
Location: .
Posts: 4,773
Default

Its true, however you have to look at the product box and on mine it said to be used only with the Spectrum system. they do a standard one for standard radios as well.

Still it works well without glitching with the Futaba 3GR synth 40mhz radio even tho Novak did recommend me not to use it unless I had a spectrum.
__________________
www.kamtec.co.uk
www.fibre-lyte.co.uk
answer-rc.com/uk/en/
Answer UK team driver
Designer of the Lazer ZX/ZXR carbon fibre tub chassis
Designer of the Lazer ZXRS
Reply With Quote
  #9  
Old 23-02-2009
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

In the end, the information that gets passed from the receiver to the ESC is exactly the same, careless whether it is 2.4GHz or 40/35/27MHz, what may change, is the frame rate at which the data is passed from the receiver to the ESC, some of the new 2.4GHz systems are very fast, so the issue may be that the ESC is designed to receiver the higher responce signals, and it gets confused maybe. But that is just daft engineering.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
  #10  
Old 23-02-2009
Welshy40's Avatar
Welshy40 Welshy40 is offline
Spends too long on oOple ...
 
Join Date: Sep 2006
Location: .
Posts: 4,773
Default

DCM - you got it in one, Novak said its been specifically designed around the Speccy system due to the way it works. I agree with what you say though and should really design the esc to recognise what its connected to.
__________________
www.kamtec.co.uk
www.fibre-lyte.co.uk
answer-rc.com/uk/en/
Answer UK team driver
Designer of the Lazer ZX/ZXR carbon fibre tub chassis
Designer of the Lazer ZXRS
Reply With Quote
  #11  
Old 23-02-2009
DCM's Avatar
DCM DCM is offline
Spends too long on oOple ...
 
Join Date: Oct 2005
Location: Marvelous South Wales!!
Posts: 8,896
Default

no, design the ESC to accept the higher frame rate, but also see the slower systems, it isn't difficult.

In the end, it is only reading a servo signal. But then, some of the HRS systems won't work with an analogue servo, as they can't accept the higher frame rate. I just think Novak are just trying to cover markets and not accept maybe small flaws in design.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man!
Reply With Quote
  #12  
Old 24-02-2009
Welshy40's Avatar
Welshy40 Welshy40 is offline
Spends too long on oOple ...
 
Join Date: Sep 2006
Location: .
Posts: 4,773
Default

Possibly right there. Explains why my servo is putting out more steering with the Novak compared to the Tekin RS Pro with the same receiver. The servo I was using was megga slow in my 2wd until I bunged in the 2.4 Novak esc (evena though my system wasnt) Mind you maybe Im just lucky that the 3GR receiver hasnt been affected and it still works.
__________________
www.kamtec.co.uk
www.fibre-lyte.co.uk
answer-rc.com/uk/en/
Answer UK team driver
Designer of the Lazer ZX/ZXR carbon fibre tub chassis
Designer of the Lazer ZXRS
Reply With Quote
  #13  
Old 26-02-2009
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

According to Novak the difference between the GTB and the GTB Spread Spectrum is that the GTB SS works at a higher frequency, this can cause RF interference problems with AM/FM radios, so it can only be used with 2.4GHz radios while the normal GTB can be used with any radio. It's not related to the servo signal side of things, either GTB version will work with both normal and high response radios.

If your servo worked better with your Novak than Tekin, there must have been a problem with the Tekin's BEC output, it shouldn't have affected the response of the servo otherwise.

The Novak HV-Max, which is probably what toooldskool's friend was using in his Losi 1/8th, is a different ESC which also has problems with AM radios because of RF interference.
Reply With Quote
  #14  
Old 26-02-2009
Cooper's Avatar
Cooper Cooper is offline
oOple Contributor
 
Join Date: Jan 2006
Location: Ghent, Belgium
Posts: 1,731
Default

Quote:
Originally Posted by ianjoyner View Post
According to Novak the difference between the GTB and the GTB Spread Spectrum is that the GTB SS works at a higher frequency, this can cause RF interference problems with AM/FM radios, so it can only be used with 2.4GHz radios while the normal GTB can be used with any radio. It's not related to the servo signal side of things, either GTB version will work with both normal and high response radios.

If your servo worked better with your Novak than Tekin, there must have been a problem with the Tekin's BEC output, it shouldn't have affected the response of the servo otherwise.

The Novak HV-Max, which is probably what toooldskool's friend was using in his Losi 1/8th, is a different ESC which also has problems with AM radios because of RF interference.
But, that does not explain the problems with normal GTB (first gen.) with 40Mhz radio's.

That is/was the main point of this discussion
__________________
www.rc-offroad.be
Never argue with a stupid man. He will drag you down to his level and beat you because of his experience.
Reply With Quote
  #15  
Old 26-02-2009
ianjoyner ianjoyner is offline
Senior Member
 
Join Date: Jun 2008
Posts: 418
Default

Quote:
Originally Posted by Cooper View Post
But, that does not explain the problems with normal GTB (first gen.) with 40Mhz radio's.

That is/was the main point of this discussion
I don't think there is a problem with the GTB and 40MHz radios? I've run one with 40MHz FM along with other people at our club indoors / outdoors / short range / long range. I know you said you and others had problems, I don't know why, but I don't think it's normal to have problems with the GTB and 40MHz.

Toooldskool started the thread because his friend had been told the Novak in his Losi 1/8th would only work with 2.4GHz, I assume this was a Novak HV-Max not a GTB.
Reply With Quote
  #16  
Old 28-02-2009
cAptainslow cAptainslow is offline
Member
 
Join Date: Feb 2009
Location: Warrington
Posts: 21
Default

Is this just the case with Novak or can it happen with other systems like SP/Losi/LRP??
Ive just got back into rc and im building up my gear and dont want to have to change to 2.4 right yet!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 10:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com