Go Back   oOple.com Forums > Search Forums
Reload this Page Search Results
Register FAQ Members List Social Groups Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 18 of 18
Search took 0.00 seconds. Search: Posts Made By: old-man
Forum: Team Durango 15-11-2011
Replies: 5
Views: 1,986
Posted By old-man
Bugle Boy shell is another alternative....

Bugle Boy shell is another alternative. Furthermore they have under tray as well. :D
Forum: Team Durango 14-11-2011
Replies: 55
Views: 10,781
Posted By old-man
Rear Shock Towers here :mad: Carbon ones on the...

Rear Shock Towers here :mad: Carbon ones on the way :)
Forum: Team Durango 18-10-2011
Replies: 5
Views: 1,251
Posted By old-man
Bugle - Sent PM to you.

Bugle - Sent PM to you.
Forum: Team Durango 13-10-2011
Replies: 334
Views: 72,260
Posted By old-man
Could anyone post the lengths of the turnbuckles?

Could anyone post the lengths of the turnbuckles?
Forum: Team Durango 10-10-2011
Replies: 21
Views: 3,210
Posted By old-man
This is really a joke. TD is expecting the new V3...

This is really a joke. TD is expecting the new V3 owners to fork out $$ for some dated wheel mounting system(hex&pin) to be fitted while they figure out how or when the new 14mm hex wheels are...
Forum: Team Durango 30-09-2011
Replies: 447
Views: 100,794
Posted By old-man
Since the V3 wheels are 14mm hex (and not seeing...

Since the V3 wheels are 14mm hex (and not seeing stores carrying 14mm wheels yet), is it possible to fit the old hex&pin from 410/410R to use the old wheels?
Forum: Team Durango 26-09-2011
Replies: 28
Views: 3,443
Posted By old-man
Mine is wobbling quite badly, so took some time...

Mine is wobbling quite badly, so took some time and did some analyzing yesterday.

So took the entire slipper assembly apart. Mounted the slipper shaft into a cordless drill and spun it very low...
Forum: Team Durango 12-09-2011
Replies: 76
Views: 8,445
Posted By old-man
I was only up by 1 decimal - so proportional...

I was only up by 1 decimal - so proportional expectations, but Durango was up a whole number - expectations is supposedly be a lot higher too. ;)

It should have been called DEX410V2.2 instead.
Forum: Team Durango 09-09-2011
Replies: 447
Views: 100,794
Posted By old-man
Bingo!!

Bingo!!
Forum: Team Durango 08-09-2011
Replies: 447
Views: 100,794
Posted By old-man
From TD "The new features on the DEX410v3...

From TD

"The new features on the DEX410v3 are:-

Big bore shocks - more consistent on rough tracks due to the larger volume of oil.

Gold shock shafts as standard – super smooth Ti Ni coated...
Forum: Team Durango 07-09-2011
Replies: 9
Views: 2,152
Posted By old-man
I noticed the same vibration but it goes away...

I noticed the same vibration but it goes away when the rear suspension is compressed or the droop is reduced with the droop screws.

Though nothing seems to be binding at full suspension travel, so...
Forum: Team Durango 31-08-2011
Replies: 16
Views: 3,156
Posted By old-man
Possibly, there is a gap of approximately .5mm...

Possibly, there is a gap of approximately .5mm between the pin and the spacer/backing. A check on how deep the pin will go into the Rulux wheel, there is only a clearance of approx. .2mm. Which means...
Forum: Team Durango 31-08-2011
Replies: 16
Views: 3,156
Posted By old-man
No, the pins are fine.

No, the pins are fine.
Forum: Team Durango 31-08-2011
Replies: 16
Views: 3,156
Posted By old-man
Thanks for the feed back. The pins are...

Thanks for the feed back.

The pins are shortened to 12mm to fit the Rulux wheels and have loosened the slipper quite a bit from stock, but still the same problem. The kit is about a month old, so...
Forum: Team Durango 30-08-2011
Replies: 16
Views: 3,156
Posted By old-man
410 Rear Wheel striped.

I have stripped a few wheels and this is annoying. I have stripped both the TD rand Rulux rear wheels. Not sure where the problem is. Anyone had similar problem and how did you fix this.

Thanks.
Forum: Team Durango 14-07-2011
Replies: 4
Views: 1,828
Posted By old-man
I had the front arm a little tight for my liking....

I had the front arm a little tight for my liking. Loosen the screws on the suspension block, pushed the arms against the suspension block and retighten. Problem went away.

Rear arms was totally...
Forum: Team Durango 12-07-2011
Replies: 3
Views: 1,971
Posted By old-man
The part number is TA-53576.

The part number is TA-53576.
Forum: Team Durango 12-07-2011
Replies: 3
Views: 1,971
Posted By old-man
I have done this on the B44.1 and TRF201 and am...

I have done this on the B44.1 and TRF201 and am very pleased with the results. Both the cars felt more consistent. B44.1 with Tamiya touring car bladders, fits like a glove.

But the TRF201 had to...
Showing results 1 to 18 of 18

 
Forum Jump

All times are GMT. The time now is 04:52 AM.

Contact Us - oOple.com - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com