Hong Nor SCRT10 ARTR
 

Hey guys,

Up for sale I have my Hong Nor SCRT10.

Hasn't been used in ages and I can't see me running it anymore to be honest, that may be because the front arm has been broke since I last used, but I didn't really enjoy running it the last time I did.

As I have just mentioned the front right lower arm has broke, I have removed this and binned it, and I now have a full set of arms on the way from Hong Kong, I also have a new front bumper coming too as the old one has seen better days.

This is the kit version so has the alloy threaded shocks and the front CVD's over the rtr version.

It's in good condition overall, however the chassis is pretty scratched up as are the side guards, I suppose that's what you get for running on gravel patches.

The truck will come almost ARTR it will require TX/RX.

It has a Hobbyking 150a ESC which has been waterproofed using liquid tape and following squirrelods guide on youtube, now I haven't tested it under water but I have happily run it through snow and rain with no effects.

The PowerHD servo has also been waterproofed using the same method as above.

The motor is a Castle-Neu 2650kv which is a replacement from Castle and has had no more than 10 runs on it, has only been run on a max of 4s. It has a AnswerRC 14t/15t pinion on there, unsure but will check.

The rest of the truck is stock as I haven't felt the need to upgrade it, with it been pretty strong in stock form.

Bad point mainly is the shell, it's got a few cracks but nothing some hot glue or fender mender can fix. I was going to buy a hot glue gun to fix it but in all honestly I don't want to spend anymore cash on the truck.

I also took out the rather pants stock battery tray and have modded a Caster tray to fit, this enables me to fit 4s fine now. I didn't drill the chassis like some people do I simply redrilled another hole in the battery tray instead, and used exisiting holes in the chassis to screw it down.

The ESC will also come with the programme card so you can tune it to how you want, however I have found the stock settings to perfectly fine.

I will also include a couple of WinForce 5000mah 2s 20c lipos, which have been perfect in the truck.

Here's some pics...

http://i527.photobucket.com/albums/c...0/IMG_1941.jpg
http://i527.photobucket.com/albums/c...0/IMG_1942.jpg
http://i527.photobucket.com/albums/c...0/IMG_1943.jpg
http://i527.photobucket.com/albums/c...0/IMG_1945.jpg
http://i527.photobucket.com/albums/c...0/IMG_2625.jpg

Underside
http://i527.photobucket.com/albums/c...0/6e8a4c3f.jpg

Don't worry the foam is now back in and the tyres have been re-glued, the shocks and diffs have all been re-oiled 35wt in shocks all round and 7/5/3 in the diffs.

The truck like I say has been rebuilt, I'm now just awaiting on parts to arrive to finish it, however if it is sold before the arms and bumper I will come to some arrangement with the buyer whether it's send the armm/bumper on, or we wait I fit them then send the whole thing on.

I have got loads more pics if you want any specific ones then let me know and I will get them.

It also comes in original box.

Price £230 insured/tracked post via courier.

Roller £110 posted.

I'm guessing this bit wasn't big enough I'M NOT SPLITTING SO DON'T ASK!! maybe now people can see it http://www.msuk-forum.co.uk/public/s...fault/good.gif

I have 100% ebay feedback for buying and selling, also on a few other forums too all with 100% feedback and with the same username carlcurtis83.

Thanks for looking.

I could be tempted by a swap, maybe another RC (not nitro), computer, 360, laptop, SLR, possibly a decent mountain bike too.