oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Ansmann Racing (http://www.oople.com/forums/forumdisplay.php?f=81)
-   -   More Problems ! (http://www.oople.com/forums/showthread.php?t=54785)

gargreen7 02-10-2010 09:45 PM

More Problems !
 
the motor will only reverse! if i hit forward i don't get anything not even a whine. couldn't think what this could be or how to over come it. any ideas ?

mark christopher 02-10-2010 09:48 PM

ur going to have to give more info

tx throttle chanel reversed
motor wired wrong

gargreen7 02-10-2010 10:01 PM

everything is on the same settings it has been, the only reverse is the servo, which works fine. the diff has currently been apart to fit new bearings but worked fine right after .

Battle_axe 03-10-2010 10:47 AM

Turn the car off and unplug then turn it on push full throttle then full break it should then be fine I take it your using the kit esc?

metalmickey0 03-10-2010 11:44 AM

You might have to reset your settings and setup the system again. Had to do the very same thing on my B4, and all i did was take motor and esc straight from SC10 and install in B4. Did nothing else but unplug and plug back in once in new car.

gargreen7 03-10-2010 05:33 PM

I've tried doing the reset but didn't seem to work, I'll try it again when I get home though.

To clarify, unplug the car. Turn on the radio, full throttle then full brake, re plug the car and try to see if it works ?

Battle_axe 03-10-2010 06:30 PM

Quote:

Originally Posted by gargreen7 (Post 419772)
I've tried doing the reset but didn't seem to work, I'll try it again when I get home though.

To clarify, unplug the car. Turn on the radio, full throttle then full brake, re plug the car and try to see if it works ?

Not quite

Unplug car. Turn on radio. Turn on car. Full throtte then full break

If that dosnt work the swap the motor wires around

gargreen7 03-10-2010 09:58 PM

half way there, it now goes forward but not backwards. i dont understand whats happening

Battle_axe 04-10-2010 01:10 PM

Quote:

Originally Posted by gargreen7 (Post 419912)
half way there, it now goes forward but not backwards. i dont understand whats happening

It sounds like you have turned off reverse get the manual out mate

gargreen7 04-10-2010 01:59 PM

could i have turned off the forward gear because it seems very very slow now ?

farmboy 05-10-2010 06:19 PM

I've come into this debate rather late but can I offer this: the Mad Rat speed controllers is a funny little thing. Each and every time you connect the battery you have to set the end points (full forward and full reverse). You have to pull the trigger on the transmitter all the way back (to set forward) and then push it all the way forward (to set reverse). Once you've done that, it's all systems go.

gargreen7 05-10-2010 07:40 PM

im trying this over and over but still get the same result, i'm sure i must be doing something wrong but i can't work out what

Battle_axe 06-10-2010 05:18 PM

Quote:

Originally Posted by gargreen7 (Post 420460)
im trying this over and over but still get the same result, i'm sure i must be doing something wrong but i can't work out what

Ok what radio you using mate? Another thing worth doing is spraying the motor out with a electrical solvent cleaner or break cleaner

gargreen7 08-10-2010 08:37 AM

using everything that came with it, i've got in contact with model sport and they said to send it back under warranty so i guess i can't argue with that


All times are GMT. The time now is 11:24 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com