X6 Anti-Squat shims
 

X-Factory X6 / Rear Hinge Pin Anti-Squat

1 piece shims in Carbon Fibre



Had some made up and been running them for over year now with out a problem.

Just back out the 2 lower chassis screws, undo the 2 screws that hold the toe-in block in place and slip in or remove a new shim to adjust the anti-squat. Kit will include a shim to replace the washers under the screws that hold the toe-in blocks in place. (when using the thickest shim the washers get in the way)

UK £10.50 shipped
USA $23.50 shipped
Europe €17.50 shipped

5 shims for anti-squat adjustment & 1 shim to replace washers used on toe-in bar (not shown)

0 deg = .150" or 3.81mm 0 deg = 3.8mm spacer or (2.3mm +1.5mm)
1 deg = .120" or 3.048mm 1 deg = 3mm spacer
2 deg = .090" or 2.286mm 2 deg = 2.3mm spacer
3 deg = .060" or 1.524mm 3 deg = 1.5mm spacer
4 deg = .030" or 0.76mm 4 deg = 1mm spacer
5 deg = no shims

UK based in the North East.

Have been racing since 1993

BRCA licence holder

PM or email if you want to get hold of some
(add X6 Anti-Squat Shimz to the subject line in email)

send payment to paypal @ [email protected]

What are they made of????
If they are required do we PM you ??

sorry I missed that out :o

made from Carbon Fibre

pm or email please for how to pay if anyone would like a set

Sorry i think it was me had one to many Largers i can now see Carbon Fibre & Pm or email :p

Oh yer whats the delivery time expected ? Cheers

these r instead of the lil plastic spacers arnt they?

sorry, im abit stupid :o :eh?: :cool:

wot sizes r they? how many do yoo get in a pack?

thanks

yes to replace the 'lil plastic washers'

me to as I've missed out some info :wtf:

5 shims for anti-squat adjustment & 1 shim to replace washers used on toe-in bar. (see 1st post)

0 deg = .150" or 3.81mm 0 deg = 3.8mm spacer or (2.3mm +1.5mm)
1 deg = .120" or 3.048mm 1 deg = 3mm spacer
2 deg = .090" or 2.286mm 2 deg = 2.3mm spacer
3 deg = .060" or 1.524mm 3 deg = 1.5mm spacer
4 deg = .030" or 0.76mm 4 deg = 1mm spacer
5 deg = no shims

working on getting 0.75mm carbon to get as close to 4 deg as possible

also, where do yoo race?

if i were to buy, i might be able to get track side,

thanks

www.trcc.org.uk

made the B final @ the regional held there :) but didn't win:(

Any markings on each one to inform what degrees antisquat they are??

Good idea though, may have to get some off you??

E

Yes I like this a lot... Will you be at the indoor finals???

I think Glenn Atterton was trying to make something along these lines, is this Glen? or part of the same thing.

OK it's me but it's Glenn not Glen:) (slip of the fingers I guess Chriss cause you got it right 1st time)

Can't make the indoor finals though due to work.

Should be some TRCC members going so may be able to have some shims @ the finals

check yor pms ;)

:p

not as yet, but then the kit washers don't come marked up either:rolleyes:

Thought about having small holes drilled in each but would put up costs due to machine time. Will see about getting it priced though. Could included a drawing like you see for turnbuckle lengths in some instruction manuals only this would be for thickness

now that's a very good idea:)

how would i be able to pay for them?

and how fast would postage be?

blablabla :p


thanks

pm'd

you have the answer

[chris not chriss :p] lol sorry ill go back to hide in my lil corner :o

Glenn,

I think these are an ace idea, I'll most likely be giving you a shout in the not to distant future. Marking the peices is a very good idea though if possible!

Dan

it's possible but,

price for parts with ID holes would need to retail @ £9.25 trackside or £10.00 posted :( (this is all due to extra machine time)

It's possile to have another batch made up today @ a push with or without holes if I phone in the order before 12:00. Next slot I have for machining will be middle of next week.

how would you like them?

Hi Glenn,
Id like them with the markings please, and I'll have two sets. Let us know if/when and we'll sort out payment.

I'll ask for mine posted, doubt I can make it to TRCC now til the next winter season.

Chriss ;)