oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Vintage RC (http://www.oople.com/forums/forumdisplay.php?f=48)
-   -   Kyosho driveshaft help (http://www.oople.com/forums/showthread.php?t=148212)

KRob 28-03-2014 06:45 PM

Kyosho driveshaft help
 
3 Attachment(s)
I've got a Kyosho Triumph in pretty good nick that will be a runner at some point (albeit rather slowly).
Only really needs the rear driveshafts sorting. It has some yellow/gold alloy ones in there at the moment. Wondered if anyone knew who'd made them?

Because of the adjustable width hubs on the Triumph they do fit but need to be on the wider setting, this makes the car too wide so I'll be replacing them with standard Kyosho items.
I know the original dogbones and axles are OT-6 and OT-18, but am I right in thinking the UJ replacements would be W5063?
Any help appreciated.

daz75 28-03-2014 06:56 PM

not sure on the numbers, but i've a number of OT-18's NIP if you need any

Naushad 28-03-2014 07:16 PM

Are they turbo rocky gold universal drive shafts?

http://www.rc10talk.com/viewtopic.ph...19856&start=30

Crashtest33 28-03-2014 08:47 PM

They are indeedy. These are the Kyosho option house universal shafts W-5062.
Bloody expensive and rare!
Didn't know they fit the Triumph but everyday's a school day :thumbsup:

KRob 28-03-2014 10:08 PM

Thanks for the RC10 talk link, why does it have to be so complicated :woot:

I don't think they are the W5062 shafts unfortunately, from all the photos I've seen they have a thicker section coming from the UJ down the dogbone for 6-7mm (at a guess) where-as these ones don't have that.

gomachv 29-03-2014 04:48 AM

Didnt duratrax sell gold colored universals for the rc10 and ultima? I can't find an ad right now but I seem to recall them. Also Trinity had gold universals iirc, but not sure if any were for optima/ultima

If those were rocky they should be a bit long on the axle side, like you might need to put a washer behind the locknut to get the wheel tight

lllyf 29-03-2014 08:43 AM

standard W5061 will replace the OT-6 and OT-18

Welshy40 29-03-2014 01:00 PM

Quote:

Originally Posted by KRob (Post 848370)
I've got a Kyosho Triumph in pretty good nick that will be a runner at some point (albeit rather slowly).
Only really needs the rear driveshafts sorting. It has some yellow/gold alloy ones in there at the moment. Wondered if anyone knew who'd made them?

Because of the adjustable width hubs on the Triumph they do fit but need to be on the wider setting, this makes the car too wide so I'll be replacing them with standard Kyosho items.
I know the original dogbones and axles are OT-6 and OT-18, but am I right in thinking the UJ replacements would be W5063?
Any help appreciated.

Measure the full length, then the length from the axle to the dog bone and also the screw thread end to the axle and let me know. I may have an alternative as i think the ujs axle is the same as the zxr.

KRob 31-03-2014 08:25 PM

Quote:

Originally Posted by Welshy40 (Post 848490)
Measure the full length, then the length from the axle to the dog bone and also the screw thread end to the axle and let me know. I may have an alternative as i think the ujs axle is the same as the zxr.

Thanks for the offer, but I think I'm going to go with the dogbones as it was originally due to the fact it won't see much action.
If anyone has worked out what these gold driveshafts are and thinks they can use them just drop me a line.


All times are GMT. The time now is 03:51 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com