oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Electrics (http://www.oople.com/forums/forumdisplay.php?f=26)
-   -   Help with Speed Passion Reventon Pro Please (http://www.oople.com/forums/showthread.php?t=133896)

spybot 04-08-2013 09:49 PM

Help with Speed Passion Reventon Pro Please
 
Just bought a Speed Passion Reventon Pro with Speed Passion Competition V3 5.5t motor. Struggling to get it to work can set neutral point, full throttle & full reverse points ok but when I switch it back on it lights up ok but will not power the motor. Removed all wires & then 're-soldered everything, changed receiver wire but still no go. Anyone got any ideas?

Steven Forster 04-08-2013 10:02 PM

I recently had the same problem when I got my new pro.....the steering was working and realised it was me not calibrating the esc to radio properly !!!

keep trying it is simple when you do it right.......my first run with esc was saturday at the NE regionals.....never had any problems ;)

spybot 04-08-2013 10:59 PM

This is how I calibrated it. I hold the set-up button down for 2 secs when switching on, orange LED lights up, red led flashes & there's a continuous beep, You then press set-up button once - orange light flashes once & there's 1 beep to set neutral position, put throttle to full position press set-up button orange light flashes twice & 2 beeps, put throttle to full reverse press set-up button orange led flashes 3 times & 3 beeps, ESC then automatically switches off. Switch ESC on, red & orange leds light up to signify normal sensored operation,moving throttle has no effect on motor.

I then completely unsoldered all wiring on batteries, esc & motor checked everything then carefully re-soldered everything. re-calibrated still nothing. I even tried calibrating it to the steering channel to see if it was a throttle channel problem, Is there anything else I can d0 please?

slippy 04-08-2013 11:29 PM

Do you have reverse. If not then try swopping two motor wires as if it has no reverse and the polarity is reversed then the motor will do nothing.

Dave.

spybot 05-08-2013 01:06 AM

no reverse. at moment it's wired yell-yell, blue-blue, orange-orange, is it safe to swap 2 wires round cos it says sensored motors must be wired up as I have done & never altered. The only sign of life I got from the motor was when I switched esc on into calibration mode then the motor was slightly pulsing but this stopped when I set the neutral position.

deepdale11 05-08-2013 05:19 AM

I had this when i brought my Pro and speed passion motor and it turned out to be a faulty motor! do you have a spare motor to try??

OneKiwi 05-08-2013 06:13 AM

Tried setting your radio TH to reverse and redoing it?

raymondkerr 05-08-2013 08:55 AM

I had a similar problem with my 8.5 pro combo abd it also worked out to be the motor, it was only 2 weeks old, I returned the motor to schumacher and got a replacement within a week and it has worked flawless every since, in fact i bought another combo this time a 7.5 for my 4wd, and that one setup first time out the box.

Try a different sensor wire then a different brand of motor to rule out the speedo.

Raymond

Soo 05-08-2013 09:40 AM

Throttle Range Setting/Calibration

A) Ensure the ESC is
switched off. Turn on
the transmitter.
B) Set the direction of
throttle channel
to”REV”
(ONLY for
Futaba Radios), set
the “EPA/ATV” value
of throttle channel to
“100%”.
C) Use a pen or
screwdriver to press
and hold the “Setup”
button on the ESC.
Release the “Setup”
button when the red
LED begins to flash.
D) Set the 3 points
according to the steps
shown in the picture to
the left
a) Neutral point
b) Full throttle
c) Full brake
E) When the calibration
process is completed,
The ESC will
automatically turn off

Steven Forster 06-08-2013 07:45 AM

Quote:

Originally Posted by deepdale11 (Post 794154)
I had this when i brought my Pro and speed passion motor and it turned out to be a faulty motor! do you have a spare motor to try??

Quote:

Originally Posted by raymondkerr (Post 794185)
I had a similar problem with my 8.5 pro combo abd it also worked out to be the motor, it was only 2 weeks old, I returned the motor to schumacher and got a replacement within a week and it has worked flawless every since, in fact i bought another combo this time a 7.5 for my 4wd, and that one setup first time out the box.

Try a different sensor wire then a different brand of motor to rule out the speedo.

Raymond

I havnt tried the new motor out yet, I just used the Pro esc with my older 8.5t motor..........guess it will be a good idea to check new motor out ASAP !!! ;)

spybot 13-08-2013 04:39 AM

Finally got things sorted. Someone suggested reversing the throttle channel the trying again & this is what I thought I'd tried but stupidly I didn't look at the labels on my transmitters reversing switches just assumed the one under the throttle was for throttle & the one under steering was for steering - WRONG!!!

Realized my mistake reversed the correct channel, re-calibrated ESC & hey presto worked 1st time.


All times are GMT. The time now is 08:20 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com