Sanwa exzes-x compatible receivers
 

I have an exzes-x with the rx451 receivers and need an additional receiver.Is there a receiver from another manufacturer that is compatible,i heard an ansmann one works but which one if it does,thanks

Hi

Like you I'm looking for a cheaper alternative, but I'm struggling. I have ansmann 3.1 compatible receiver, but it will not bind. I saw something about using a different mode so switched to fh2, but no joy.

I think the issue is that the x is fhss2 or fhss3, whereas the plus is fhss so therefore compatible. I could be wrong as I don't know anyone with a plus.

Would be interested to hear if you do find something.

Steve

Sorry to drag up an old post but did anyone find anything that would work?

Cheers

I've been using an Ansmann R3.1 without any problems but not sure if you can still buy them. I think there is an LRP reciever that also works with the Sanwa but not sure witch one it is

The ansmann r3.1 does work u have a couple of them and use 1 with my exzes x just change the mode to fhss2 and bind as normal easy

LRP is the C3-RX

One further question to this

If I have an old m11 with Sanwa 2.4 module fitted using ansmann 3.1 rx. Can I buy a new Exzes and use a new rx and ansmann 3.1 rx without constantly changing settings. Ie can you have it setup for one model to use the 'old technology' and setup on a different model memory to use the new tech

I hope I make sense

Just makes me think it could be a good way to save costs

Yes mate. You can have each model on a different modulation mode if you like. Eg, model 1 on fh2, model 2 on fhss3 etc. All settings are individual to each model in the memory.

hmmm that seems very positive

saves me a heap of cash and can keep the old m11 for someone to use to race against. - would this be the same though with any sanwa

so an mt4 m11x and m12?

It is the same with the Gemini X and the MT4, not sure on any others but I think all of their dedicated 2.4GHz systems run similar configuration firmware.

I've just got the Exzes Z and its the same except it runs higher speed at the top end I believe. Good news is it works all my older rx's too including an Ansmann. :thumbsup:

digging up an old post again.... anyone found any other receivers current or old working with exzes X ?????

The 371w works. Cheap and waterproof! Little bigger than the other receivers but worth a look.

Im actually after some small rx's now for the exzes z, b44, b5m, sv2.
So for the 2wd the smaller the better.
So is that correct the ansmann ones work with the Z ?, well if anyones got any kicking around please let me know, sanwa ones are expensive and ansmann ones seem hard to get.

Can't understand why you buy an exzes z and then scrimp on cheap receivers? The z is fhss4 but the cheapo ansmann type ones are fhss2 at best. Like buying a Ferrari and sticking a fiesta engine in it.

Calm down if your not gonna be helpful then why post, had a bad day or something ?

The reality is i like the feel and weight of the exzes and if you dont mind spending on over priced receivers then fine, but i dont.
Response times mean nothing to me i just wanted a new sanwa transmitter is that ok ?

No I've had a fantastic day actually, just pointing out that the cheaper receivers are way slower than the proper ones. Maybe other readers might find this info useful even if you aren't bothered.

With your somewhat aggressive response maybe its you who's had a bad one?

Not aggressive at all i just wasnt aware there was actually a big noticeable difference with speed thanks you made me think again about scrimpin im gonna order a proper receiver now.

Thanks again

soo what abou the ansmann w5/w6 receivers , are they compatible too ?

Sadly not shaun.

As for the speed difference I can tell the difference between the RXs on FHSS2 and FHSS3, not got a TX that will do FHSS4 so can't tell you how much faster that is but it should definitely be noticeable.