Durango Big bore tapered pistons
 

Just to let you all know I now make tapered pistons for the Durango Big bore shocks!
http://www.gurnellrc.com/ForumImages...ns/Pistons.jpg


There is a choice of 2,3,4,5,6 holes pistons with 1.0 mm to 1.7mm in .05mm steps.

chart of total area in pistons


http://www.gurnellrc.com/ForumImages...istonChart.jpg

Please PM me if you are interested in purchasing a set. I’m selling then at £6 a pair with free postage.

Nathan Waters has been running the pistons for the last 2 Nationals with great results with A finals at both Nationals!


Link to Nathans Talywain setup
http://www.team-durango.com/pdf/setups/TD102001/Talywain_GB/DEX410_Nathan_Waters_Talywain_BRCA_National_Round_ 3_29_05_2011.pdf

thanks for the order people will get them posted tomorrow first thing

Just to say all orders have been posted today many thanks for the orders everyone.

Also Adam was running my pistons at kidderminster National here is a link to his setup. Car look great through the bumpy section off the straight.

http://www.team-durango.com/pdf/setu...g_19_06_11.pdf

Link to Adam Skelding grass setup from Oswestry national using the taper piston!

http://www.team-durango.com/pdf/setu...g_10_07_11.pdf

Also all piston orders have been posted out tonight :thumbsup:

Just to say all orders have been posted out today

many thanks

Nick

Just to let you all know that all piston orders are going out tomorrow! thanks for the orders

DO NOT sell any to lazy arse coleman! He needs to do it himself :D

Just to say all orders have been packed and are in the post tomorrow! Happy 210 building :thumbsup:

Hi all just to let you know all piston orders have been post! Also I have added some link below to the 210 setup on the Durango web site using my pistons as I have had a lot of Pm about hole size! Hope this helps a little

Links to 210 setup using Tapered pistons

Stotfold Astro outdoor

http://www.team-durango.com/pdf/setu...16_10_2011.pdf

Taplow carpet/slippy board

http://www.team-durango.com/pdf/setu...23_10_2011.pdf

Worksop indoor cork/carpet

http://www.team-durango.com/pdf/setu...09_10_2011.pdf

http://www.team-durango.com/pdf/setu...09_10_2011.pdf

York indoor carpet/polished floor

http://www.team-durango.com/pdf/setu...15_10_2011.pdf

Just to let you all know all Durango piston orders have been posted out at lunch! Also here are a couple more links to setups on the durango site for the DEX210 using the tapered pistons


Broxstow damp astro

http://www.team-durango.com/pdf/setu...13_11_2011.pdf

worksop indoor round 2

http://www.team-durango.com/pdf/setu...06_11_2011.pdf

http://www.team-durango.com/pdf/setu...06_11_2011.pdf

Just to say thanks for the orders and they have all been posted at lunch :thumbsup:

:thumbsup:

Just to say all pistons ordered before 11 last night have just been posted:thumbsup:
Many thanks for the orders and happy New Year

Hi all piston orders have been posted out! See you all at area 51:thumbsup:

Nick are you bringing any pistons with you to Area51?

I had a very busy week so not had time to make many but will have a very small amount with me. Will be there from around 6 tomorrow

kind regards

Nick

Are you making anymore of these pistons?

Pistons
 

Send Nick a pm as he normally makes them too order. They are a real quality bit of kit.

Hi i have most size in stock and make a batch a week at the moment. If you would like some just send me a Pm with what you after

kind regards

Nick

Hi all just to say all orders have just been posted:thumbsup:

Hi all! All orders was posted out last night :thumbsup:

Hi Nick,

How do one pay you, via Paypal ?

Rgds.
Erik

You have Pm Erik

Hi all just to say all orders have just been posted :thumbsup:

Just to say many thanks for all the orders and they have all been posted today :thumbsup:

Hi all just to say thanks for all the orders. They have all been sent :thumbsup:

Hi just to say thanks for the orders and the have all been posted hope you all get for the weekend! :thumbsup:

Nick,
Will you also make non-tapered pistons?
Thanks.

I have machined some blanks today with a rounded corners (like a losi small bore piston) so should have some by next week.

Hi Nick , i´m very interested in your pistons... is it possible to send them to germany ? is there any possibility to pay using a normal money transfer ?

Thank´s for your answer !

Regards

Jens

Hi yes you can pay with money transfer and yes i can send to germany. If you Pm with what details you need i will send them over.

Hi all just to say thanks for all the orders and they have all been posted :thumbsup:

Are you still making these? PM sent

Hi all just to say all orders have been posted out today :thumbsup:

Cheers for all you help mate

Cheers Jordan

Just got my order from Nick. Pistons look great! Can't wait to hit the track with them! Thanks bud!

Hi Nick,
Can you make non-tapered pistons (rounded edge) for Durango big bore with 3 holes of 1.3 mm?
If yes, pm with the details, I have PayPal.
Thanks.:thumbsup:

I picked up some pistons for my 210 and 410 at oople and just wanted to say they make a massive improvement over the kit style.

The shock travel is so much smoother.

Will have get a good stock of different sizes in for future.

Thanks nick

:thumbsup:

Is Nick still making pistons?
Long time no hear!

Could you please explain what the difference is with the standard BB-pistons in terms of advantages, disadvantages, reaction, ...
Why should one use these?

And have you allready considered making and selling blancs so that the driver can drill the holes of his choice in them?