Ansmann buggy gallery
 

Havent seen a gallery here so thought I might start one.

Heres mine.
Started with a stock Madrat Im sure you are all familar with it but will post a pic anyway, with an ezrun combo + HK controller

http://i30.photobucket.com/albums/c3...a/DSC00423.jpg


Now I have a Team C TC02/ X-PRO tekin motor HK esc but looking for a better one (as it doesn't really fit, let me know if you have one available) and have a spektrum DX3E TX/RX
35W oil
Kyosho yellow springs
3A/3B piston
KO PS-2113 from tyreman thanks

http://i30.photobucket.com/albums/c3...a/73685111.jpg

http://i30.photobucket.com/albums/c3...a/DSC00473.jpg

http://i30.photobucket.com/albums/c3...a/DSC00472.jpg

What do you think about the mounting of the esc?? Its the only place I can put it as its too big for the right hand side

Im waiting for panther slicks for the car so I can drive it like I stole it at our carpet track at the local

I had an extra green original body was going to paint it black but that ran out so it became red. going to have black windows later

Here's mine
http://i247.photobucket.com/albums/g...c/IMG0033A.jpg

http://i247.photobucket.com/albums/g...c/IMG0034A.jpg

nothing special, just the old tank of a Master Smacker i used for the Ardent winter series, not expecting to win much with it but my aim is just to not come last. Fitted with 9t /35a ezrun system (was contemplating a 5.5/60a system), basic Futaba S3004 servo & the competition regulation mini-pin tyres on Fastrax rims (the only ones i could get to fit because of the off-set) with blue inserts, running Spektrum DX3S radio gear.

The only other changes i made were i fitted an ARE-1 spur gear (2 teeth less) because i stripped the kit one during the 1st run - (tip: don't follow the manual when meshing, put the top deck on before meshing the spur), plus i fitted a Tamiya pinion because the kit one weighs a fair bit & i've also changed the shock oil to Schumacher 30wt & fitted rubber collars inside the dampers on the shock-shaft to limit the travel to help with landing & to stop squat when i nail the throttle. I also tried springs on the rear from the Tamiya kit shocks of my DF-02 buggy. the kit springs really need to be softer as there is a lot of rebound as you land the car off a big jump, but it's just finding ones that will fit.
Plus a few changes to what the manual suggested were fitting the steering with pivot balls from the ARE-1 kit which aren't shouldered otherwise if you use the ones from the kit with the shouldered pivots, the steering linkage fouls & limits the travel.

will post a pic of the Mad-rat i've recently got when i get round to building it. I also have an Ansmann ARE-1 touring car but i won't bore you with that. ;)

http://i677.photobucket.com/albums/v...1/cd4fd6dc.jpg
Rob Jacques at the Players

http://i463.photobucket.com/albums/q...1/IMG_0018.jpg

Ash Peatman's new X2C

nice.. ^^what was /is he running in that? what mag was that from?

My 1st X pro with the mad rat bodies (Not new)

http://lh6.ggpht.com/_sxeWYpX_f90/TA...s/IMG_7957.JPG

The inside with SP GT 1.1and 10.5 SP
http://lh6.ggpht.com/_sxeWYpX_f90/TA...2/IMG_7962.JPG


I was really with the 1st one so I buy a another but a new one
http://lh4.ggpht.com/_sxeWYpX_f90/TP...0/IMG_9568.JPG

I haven't picture with electronic instalation. But in putt a robitnic ESC 8.5 and motor 10.5 robitronic too.

After i see the kit transformation, so i take my 1st X pro for a lifting :D
http://lh3.ggpht.com/_sxeWYpX_f90/TO...0/IMG_3457.JPG

I change the motor for 10.5 robitronic an a low profil servo.

And in last i buy the X2 TE, so i take the electronic of the 2nd X pro (know for space part)
http://lh4.ggpht.com/_sxeWYpX_f90/TS...MG_4917_GF.jpg

1st for X2TE this week end :)

Looking good mate. To be honest you don't need a cooling fan on your esc when running 2wd. If you removed the fan would it fit on the RHS? should then give a lower C of G and more even weight distribution.

Thats what I was thinking but it being a hobbyking esc and the fact that I burt a 35A $15 dollar one after 2 runs around the track.

This esc is not much better I think being a 60A $30 one.

If I did remove the fan I think the rx and switch connectors might rub but those I can solder in place ( Thats an idea)

Ill test it as it is tomorrow at the track and ask a couple others there but would like feedback from others about not needing a fan. Not that I don't trust ya Chris just nice with more input

What motor were you running on that speedo to blow it? I know very few people who attach a fan to their 2wd speedo as overheating is rarely an issue. If it is then cutting a couple of vent holes in the shell often works - quite common in 4wd cars.

.
 

My X-pro with conversion
http://www.oople.com/forums/picture....448383&thumb=1http://www.oople.com/forums/picture....448190&thumb=1http://www.oople.com/forums/picture....447935&thumb=1http://www.oople.com/forums/picture....447935&thumb=1http://www.oople.com/forums/picture....447614&thumb=1

Andy

.
 

double post

Im running a Tekin Redline 278 looking at the specs I think it maybe a little too fast with 2,5T 7800Kv

You got 2 of the same car andyp??

This is my X2TE - Limited Edition no.36

Options:
alu front tower

Electronics:
Savöx BLH-3650 - 5000kV sensored brushless motor
Savöx NBC-50c sensorless ESC
Savöx SC-1257TG steering servo
Turnigy 5000mAh 2S1P 20C hardcase LiPo
Futaba 40mHz FM Receiver
AMB-IT RC4 hybrid transponder

Tires:
Front - Mad Rat original
Rear - Mini Spikes (Conrad)

More pictures:
introduction of my Ansmann X2 TE Limited Edition

http://www.rc-junkies.nl/news/wp-con...ad_rat_001.jpg

http://www.rc-junkies.nl/news/wp-con...ad_rat_011.jpg

http://www.rc-junkies.nl/news/wp-con...ad_rat_007.jpg

http://www.rc-junkies.nl/news/wp-con...race_2_016.jpg

Where can I get oe of them xt2e limited edition and how much?

Thats taken from the 30th anniversary edition of radio race car international (february edition) Availiable from all good newsagents. Well in the UK anyways. :lol: I came fifth in the open class at the players 2010(although i could have been on the podium if it had not been for a breakage when trying to overtake open class champion Andy pearson :cry: Still it has to be said that was the best, most intense race I have had in a long time)

In the photos is what I am pretty much running today. The car was kit standard apart from a slight mod on the back end to get more anti-squat. Electrics wise it has a savox servo, LRP SPX (I usually run a Nosram but I left it in my spare car) LRP X12 6.5(Which is a bit hot for 2wd but it is the only 6.5 I have :lol:) and my trusty two year old team orion 4800s.

Only things I have changed since then are I am running 30 degree alloy caster blocks on the front and also a rubebits under servo weight. The X-pro was excellent at the weekend and was the only rear mounted 2wd car in the A final at West bridgford I think.

Sorry double post..

all looking very nice.Ill get some pics of my cars and the mods listed in my other post some time this week.

Heres my rides.

http://i14.photobucket.com/albums/a3...02f3aac_0f.jpg
http://i14.photobucket.com/albums/a3...know/22222.jpg
http://i14.photobucket.com/albums/a3...Picture283.jpg
http://i14.photobucket.com/albums/a3...w/IMG_1636.jpg

nice ^^

BTW I took the fan off tonight and it ran fine Im going to sell the tekin motor and get something else let me know if any1 wants it

I'm liking that shell lots. That looks gorgeous.

Where did you get it, as I wouldn't mind a bit of that?

A picture of my Ansmann X2TE

Here it is...

Here it is...I hope!:eh?:

looking good, do you or any one have a rear end pic of the x2c with the alloy hubs fitted?

You want to know who painted them?? Chuck at ridgewaybodies.com:thumbsup:

Here's how mine is looking these days... Just ordered up my CF sheet to mill all my shock towers :) the front tower is currently G10 compound.

http://4.bp.blogspot.com/_nAb8ZS46_R...0/SDC10678.JPG

J

here s mine just need a chance to run it now as its all ready to run:thumbsup:

Here is my X4 pro:

http://i1046.photobucket.com/albums/...g?t=1295724551

I've fitted following upgrades:

Big bore shocks
Aluminium front brace (black upgrade)
Aluminium castor blocks
CNC heatsink motor mount
Plastic shock tower guard

Currently running Xcelorin 6.5 motor, Speed Passion GT2 pro esc, Spectrum DX3 radio and Savox 1251mg servo

http://i1046.photobucket.com/albums/...g?t=1295724551

X2c Buggy
 

hi all, thought i`d post my pics here, it`s my first buggy, been racing tourers for years and fancied a change. Kit Standard, but its early days, we`ll see how it goes!!

Nice car John - are you racing buggy this friday?

This shell is for my doughter´s x2pro

http://img801.imageshack.us/img801/7167/x2pro.jpg

Here's my x2c ready for the season

Big thanks to Mark A for the shell great work

Madrat
 

Here is a few pics of my Madrat. Got the kit for Xmas and since then I have done a few upgrades namely

associated alloy shocks
ball raced
upgraded turnbuckles
17t schaumacher goldrush brushed motor
24tooth pinion
front staggered rib yet to fit.

Not too keen on the madrat shell so opted for something a bit different...

Just finished painting my first ever bodyshell. Its a proline bulldog shell for a b4.1. I know its not everyones cup of tea but I love the shape of it. Had to cut and trim away some shell to get it to fit.

Ive ran it at Torch racing club 3 times now and it goes very well considering its a budget buggy. It has stood upto a few crashes but amazingly is still in one peace. Diff is still fine as well:o.

Planning to upgrade to brushless soon once I get competent with the track.

A fantastic little car and great value for money.

a feww pics....

http://i146.photobucket.com/albums/r...x/DSCF1007.jpg

http://i146.photobucket.com/albums/r...x/DSCF1009.jpg

http://i146.photobucket.com/albums/r...x/DSCF1008.jpg

http://i146.photobucket.com/albums/r...x/DSCF1001.jpg

http://i146.photobucket.com/albums/r...x/DSCF1014.jpg

wow I like that where you get the shell from?

bodyshell
 

Got it on ebay.

Ordered on Wednesday and got it next day:o.

Here is the link..

http://cgi.ebay.co.uk/ws/eBayISAPI.d...=STRK:MEWAX:IT


James

Depends if he has fixed it yet :lol:

So I turn my back for 1 week and everybody breaks their car:lol:. Glad I am racing this friday - should restore order at the club:p

My Carpet SX10
 

http://pages.videotron.ca/jaunerc/midcarpet2.JPG

http://pages.videotron.ca/jaunerc/midcarpet1.JPG

http://pages.videotron.ca/jaunerc/midcarpet3.JPG

nice john...Any pics with the body off?

hej... keep those kinda comments to the adult sections :p yeah john whip the top off for the boys!!

Here's my work in progress:

http://www.oople.com/forums/picture....pictureid=3821

http://www.oople.com/forums/picture....pictureid=3822

http://www.oople.com/forums/picture....pictureid=3823

http://www.oople.com/forums/picture....pictureid=3824

Just looking for a nice looking shell now, plenty of suggestions, maybe HPI E-Firestorm