Heavy Duty Adjuster TRF511
 

hi

hi where can I find Adjuster as if the picture

I can only find the orignal with this part number Tamiya - 51283

someone has a part number

I hope someone can help me

I am a TRF511 to build nou

Thanks guys

I'm sorry for my english i am dutch

I don't think they have been released yet!

But there was a lot of them to be seen at Taly! :confused:

Just mailed Champ on this very part, will let you know what they say.

P.S Cool blog Simon, just spent 4 hours reading it!

thanks mate

I think they are only for team drivers are from Tamiya

You see them only at the team drivers cars

Unless you want to bling up your ride, I do not see the point in the blue
turnbuckles. The stock steel ones are strong!
I think the car looks better with the silver turnbuckles...just my opinon.
Too much blue bling is a bad thing. The tottally destroys the look of the car.

...because everyone wants to know what you think about blue turnbuckles.

DELETED

not the turnbuckles but adjuster

cheers marco

I didnt notice any

Those blue turnbuckles give me a semi, im ordering some

nobody can help me :(

Most of us can help, but it will be without Tamiya ball studs and cups....

HPI studs (75115 & 75116) with Losi grey rigid cups (LOSA6016) are a great solution!

thanks mate

Will a pack of each of the Hpi ball studs be enough to do a car??

Also will a pack of the losi ball cups do a car too?

I use LO-A-6015 (white Losi ball cups). 16 ball cups/pack.
Ball studs HB-61582 (13 mm) and HB-61581 (10.3mm). 8 ball studs/pack.

Or as Aaron said:
Losi grey rigid cups (LO-A-6016)=16 ball cups/pack.
HPI studs (75115 & 75116)=4 pieces/pack

I purchased from rcmodel.com.hk.

Tamiya grey ball cups should be available when TRF201 is released.

he wants to know how many sets of ball studs to buy

I am just about to do an order, but how may packs of:

Ball studs HB-61582 (13 mm) and HB-61581 (10.3mm). 8 ball studs/pack.

Will I need to do the car??

Kyosho ball cups fit on directly to the tamiya balls and is what i used on my 501x

Yep, they do, the big long ones are nice n strong. I'm going to have them on mine when I get fed up of the kit black ones...

Thats an easier option! Do you happen to know the part no??

Kyoshos Hard Ball End Set 97021H

There's 12 big uns and 4 tiny uns in the pack.

UM112 but you will need to buy two lots for your car as there is only six long ones in each pack.

UM112 aren't the big long ones?

Once I know what part no to order I think I am going the Kyosho route as the HB ball studs are a bit of a pain to get at the moment.

Kyoshos Hard Ball End Set 97021H

Google that part number and you'll see they should be what you want.

You can also use two of the very short Kyosho ball cups (that come with the set that Simon linked above) for the servo turnbuckle/linkage. They are the same length as the short Tamiya cups. :)

Good stuff! I have just ordered a set up and see how they go!

I didnt know about this one, thanks for that.

Something I can order as well instead of the normal ones, and looks better than UM112. Cheers.:thumbsup:

bump

are the new ball cups available to the public, which only the team drivers had access to?

want my 201x built right from the start, when I get it

I'll say it again...

I want tamiya ball cups on my 201x, as I already have tc5 ball studs/losi white ball cups on my current car.

Just changing to good ball cups is the easiest to achieve.

Does anyone have the part number for the trf ball cups?

201 comes with new grey ballcups. No need to change them.

The part number in the TRF201 manual for the ball cups is the same as the ones previously used in the 511. I don't think these are newer ones unless tamiya made a running change without updating the part numbers?

yes and also the ball cups used on the 201x are the same as the db01, which everyone is swapping out for stronger ones.

maybe they will never be released

Trust me, 201 comes with new grey ball cups. Take a look in the 2wd thread.
Tamiya made a running change without updating the part numbers.
Here´s a pic:
http://i185.photobucket.com/albums/x...3/DSC01787.jpg

any ideawhere to get the "new" adjusters from, not the old ones considering they have the same part no.

Coming soon.....:thumbsup:

how soon:confused::confused::confused:

I need some of these for Sunday's regional at DMS, as the kyosho ones I have on my 511 need replacing, are they in the country yet?

I know the hobby company still have the old ones, as I called them yesterday. Has anyone been using the old ones? What are they like?

If anyone has any spare then please pm me paypal waiting.

I'm sure I'll be the only one to say this but....I prefer the old ones!! Have not popped a turnbuckle in over 6 mtgs with them! I have a feeling they just had a bad batch tbh..