X6 Anti-Squat shims
 

X-Factory X6 / Rear Hinge Pin Anti-Squat

1 piece shims in Carbon Fibre



Had some made up and been running them for over year now with out a problem.

Just back out the 2 lower chassis screws, undo the 2 screws that hold the toe-in block in place and slip in or remove a new shim to adjust the anti-squat. Kit will include a shim to replace the washers under the screws that hold the toe-in blocks in place. (when using the thickest shim the washers get in the way)

UK £10.50 shipped
USA $23.50 shipped
Europe €17.50 shipped

5 shims for anti-squat adjustment & 1 shim to replace washers used on toe-in bar (not shown)

0 deg = .150" or 3.81mm 0 deg = 3.8mm spacer or (2.3mm +1.5mm)
1 deg = .120" or 3.048mm 1 deg = 3mm spacer
2 deg = .090" or 2.286mm 2 deg = 2.3mm spacer
3 deg = .060" or 1.524mm 3 deg = 1.5mm spacer
4 deg = .030" or 0.76mm 4 deg = 1mm spacer
5 deg = no shims

UK based in the North East.

Have been racing since 1993

BRCA licence holder

PM or email if you want to get hold of some
(add X6 Anti-Squat Shimz to the subject line in email)

send payment to paypal @ [email protected]

What are they made of????
If they are required do we PM you ??

sorry I missed that out :o

made from Carbon Fibre

pm or email please for how to pay if anyone would like a set

Sorry i think it was me had one to many Largers i can now see Carbon Fibre & Pm or email :p

Oh yer whats the delivery time expected ? Cheers

these r instead of the lil plastic spacers arnt they?

sorry, im abit stupid :o :eh?: :cool:

wot sizes r they? how many do yoo get in a pack?

thanks

yes to replace the 'lil plastic washers'

me to as I've missed out some info :wtf:

5 shims for anti-squat adjustment & 1 shim to replace washers used on toe-in bar. (see 1st post)

0 deg = .150" or 3.81mm 0 deg = 3.8mm spacer or (2.3mm +1.5mm)
1 deg = .120" or 3.048mm 1 deg = 3mm spacer
2 deg = .090" or 2.286mm 2 deg = 2.3mm spacer
3 deg = .060" or 1.524mm 3 deg = 1.5mm spacer
4 deg = .030" or 0.76mm 4 deg = 1mm spacer
5 deg = no shims

working on getting 0.75mm carbon to get as close to 4 deg as possible

also, where do yoo race?

if i were to buy, i might be able to get track side,

thanks

www.trcc.org.uk

made the B final @ the regional held there :) but didn't win:(

Any markings on each one to inform what degrees antisquat they are??

Good idea though, may have to get some off you??

E

Yes I like this a lot... Will you be at the indoor finals???

I think Glenn Atterton was trying to make something along these lines, is this Glen? or part of the same thing.

OK it's me but it's Glenn not Glen:) (slip of the fingers I guess Chriss cause you got it right 1st time)

Can't make the indoor finals though due to work.

Should be some TRCC members going so may be able to have some shims @ the finals

check yor pms ;)

:p

not as yet, but then the kit washers don't come marked up either:rolleyes:

Thought about having small holes drilled in each but would put up costs due to machine time. Will see about getting it priced though. Could included a drawing like you see for turnbuckle lengths in some instruction manuals only this would be for thickness

now that's a very good idea:)

how would i be able to pay for them?

and how fast would postage be?

blablabla :p


thanks

pm'd

you have the answer

[chris not chriss :p] lol sorry ill go back to hide in my lil corner :o

Glenn,

I think these are an ace idea, I'll most likely be giving you a shout in the not to distant future. Marking the peices is a very good idea though if possible!

Dan

it's possible but,

price for parts with ID holes would need to retail @ £9.25 trackside or £10.00 posted :( (this is all due to extra machine time)

It's possile to have another batch made up today @ a push with or without holes if I phone in the order before 12:00. Next slot I have for machining will be middle of next week.

how would you like them?

Hi Glenn,
Id like them with the markings please, and I'll have two sets. Let us know if/when and we'll sort out payment.

I'll ask for mine posted, doubt I can make it to TRCC now til the next winter season.

Chriss ;)

Batch of shims ordered today with ID holes.

0 deg = 3.8mm spacer / no holes (you can't drill 1:wtf: )
1 deg = 3mm spacer / 1 hole
2 deg = 2.3mm spacer / 2 hole
3 deg = 1.5mm spacer / 3 hole
4 deg = 1mm spacer / 4 hole

Hi Glenn,

Can I have a set with ID holes sent to me please. Let me know you're Paypal and I'll send you the money and my address.

Cheers,

Dan

details pm'd

HI Can I have a set with ID marks please.

details PM'd

BIGGER pix added, see 1st post

shim behind screws for toe-in block will be changed slightly so that it becomes captive.

missed out on the above:(

For those that have paid I hope to have items in post on Wed next week latest.

Will post as soon as I know more.

see post 26

missed the dead-line on Friday :(

anybody wanting to buy a set of the shimz (thanx Chris) for the X6 or Pan-Cars ( see Flat Stuff thread) you can now pay me @ paypal using

[email protected]

for those that have ordered and paid thanx:)

posting items out 1st March

sorry you've had to wait a little longer than I anticipated

Shimz kits now come with this item and not the origanal 1 you see in 1st post. (scanned image)

http://snap33.photobox.co.uk/9161451...3becedd759.jpg

off to the Post Office now to get back orders posted

stock level down to 5 kits

racing @ the Indoor Finals - York 24/25th March with the X6 ?

not got your Shimz yet?

you've still time to order

cut-off date so I can have any orders ready will 16th March

hope to have a TRCC member there with some if you miss the dead line (I can't make it due to work, unless i throw a sicky:))

don't miss out on the above date if you want the Shimz for or @ the Indoor Finals

email
[email protected]

X6 anti-squat shimz
 

will have some with me @ the weekend @ NERCR regional :)

how much do they cost for the full set?? i might be interested in buying some at NERCR

from 1st post in thread

£9.25 trackside or £10.00 posted (with ID holes)

2 more sold @ the regional :)

2 pair left

:) X-6 Shimz / Now shipping World Wide :)

well France that is.

now if I can crack the American market I'll be financially sound :D :D :D

:cool: :cool: :yawn: ;)

Give those shims a good work out @ the Belguim GP this weekend. Be nice to see them on the podium :)