Our go at a lipo X6
 

Our go at a lipo x6...

Here are some pics of our attempt at a lipo x6 we filled the front battery slots with some apoxy putty up to the little brace bit and then filled the rear battery slots but still allowing room for lead. We also filled the spare screw holes for the 3 gear box and put screws to hold the wing instead of the clips. And finally sprayed his shell which is still drying. here are some pics.....

http://img129.imageshack.us/img129/1951/dscf0867vw1.jpg
http://img129.imageshack.us/img129/d...jpg/1/w800.png

http://img129.imageshack.us/img129/5262/dscf0871ed5.jpg
http://img129.imageshack.us/img129/d...jpg/1/w800.png

Ashley and Jono

Attachment 4742

Attachment 4743

Bodyshell done nice and simple....

http://img210.imageshack.us/img210/7602/dscf0873jq7.jpg
http://img210.imageshack.us/img210/d...jpg/1/w800.png

A

Looks rather cool :D

Nice dremel work on the chassis :thumbsup:

It was unchartered ground was difficult to try and get it tidy. Jono dremmeled it i sanded it.

A

lol its not as bad as the photos make it look its all neat and tidy in the chassis, the wing mounts where easier than i thought they were gonna be to

Looks good!

I'd move the rear camber link out though, ideally the E Speed hangers of course ;)

Is that a receiver pack???

Look like the caps that come with the Speed Passion esc's

Correct :thumbsup:

on order:thumbsup::thumbsup:

Where did you get the putty from mate.

got from halfords its made by araldite its two part and you jus cut off what you want and mix in your hand be quick though as its rock jard in about 10mins

What slipper and spur gear set up is that?

Looks like an RW Racing spur with a B4 slipper set-up

Losi spur and pads AE spring plates still tryhing to figure out how to fit the losi slipper.

A

Try milliput m8 in black its on flebay mold it into the slots smooth of with water and leave till morning :thumbsup: it sets rock hard think its epoxy based

Sounds like the stuff to get cheers :thumbsup:

Er.... you just put it on Ash. The slipper plates have the same key to the layshaft, you just need the short spring for the hydradrive.

G

Locating the spring is the only thing, you have to drill out either the small spring locator washer or the big load distributing spring locator thing. Defo need the short silver Hydra spring though.

You dont need to sand the bottom of the chassis, just put duc-tape on the bottom. Flip the chassis and fill the slots, and let it dry overnight.

if you desire you can push in lead inserts into the epoxy while it is drying. I use the sheet lead they use to seal roofs. when cut to size there about 18g. per slot (see 3rd pic). I have 4 of those, and got a 40g plate under the ESC

btw, I like you paint. Looks just like mine :D

Just use the AE one..seems to work perfectly fine to me. Just make sure you run the white pads as the yellow ones are a little snatchy!!!

Ok thanks for the help ill talk to jono see what he wants to do. Not even my car lol.

A

I havent had much run time with the car yet i dont see why the b4 slipper wouldnt be up to the job

Do the RW spurs fit straight onto the B4 slipper? What sizes do they come in?

Still waiting for the AE 72/75 spurs to be available so these might be an option.

Cheers,
Scotty P.

yeah it fits straight on but i am using losi slipper pads