oOple.com Forums
Page 7 of 13 « First 56 7 89 Last »
Show 40 post(s) from this thread on one page

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Schumacher (http://www.oople.com/forums/forumdisplay.php?f=46)
-   -   CAT SX is here! (http://www.oople.com/forums/showthread.php?t=14106)

peetbee 19-09-2008 02:20 PM
Quote:
Originally Posted by Northy (Post 161231)
And will be ACE :thumbsup:

See why I thought it would be so good? More sales of pins for me:woot:

G
Edited for accuracy ;)

Chrislong 19-09-2008 02:23 PM
Nortech pins don't snap, its a worthy purchase, its an upgrade from the rollpins on the hexes.

Northy 19-09-2008 02:24 PM
That is as long as they are the right size, we'll try tomorrow night Chris :woot:

G

Chrislong 19-09-2008 02:29 PM
No worries, bring some calipers - we'll measure them up :thumbsup:

mark christopher 19-09-2008 03:09 PM
these nortech bits, got any links to em all?

Chrislong 19-09-2008 03:38 PM
Quote:
Originally Posted by mark christopher (Post 161246)
these nortech bits, got any links to em all?
http://www.nortechracing.co.uk/

No matter where I navigate to, my URL bar always says the above - so I can't link to any specific pages, sorry mate.

glypo 19-09-2008 03:56 PM
http://nor-tech.gforceimages.net/sto...x.php?cPath=31

These I assume.

ben 19-09-2008 03:57 PM
G the front pins were my idea!!!! Dont you be taking all the glory :woot:

Cruise 19-09-2008 07:31 PM
Just finished the basic built of mine.Thankfully I have prewired electronics to put in.

Cruise.

GRIFF55 19-09-2008 09:34 PM
Stupid question here, how do you adjust the pinion meshing?

Mossy 19-09-2008 09:40 PM
2 screws fix the motor clamp to the alloy housing underneath the chassis, and a 3rd slots in and tightens on the side. Undo all 3, move and tighten back up.

Even when u change motor the pinion meshing wont be affected as the clamp is already fixed to the correct position. Simple as really, and allows you to change motor and mesh in under 20 seconds lol (yes i have tried it!)

ashleyb4 19-09-2008 09:48 PM
Quote:
Originally Posted by Chrislong (Post 161239)
Nortech pins don't snap, its a worthy purchase, its an upgrade from the rollpins on the hexes.
Holy WOW didnt expect Chris to change to the CAT good luck next eyar with it chris :)

A

ben 19-09-2008 09:51 PM
Why did u expect chris to change to schumacher ash?:confused:

ashleyb4 19-09-2008 10:00 PM
Typing error ben.

A

ben 19-09-2008 10:01 PM
Quote:
Originally Posted by ashleyb4 (Post 161387)
Typing error ben.

A
Whatever.

chris68nufc 19-09-2008 10:07 PM
Building mine at the moment. Ive built the diffs then rebuilt them but still feel notchy. Will they smooth out when i run it? The car goes together very well and instruction book is very good. Easy even for me!

MattW 19-09-2008 10:41 PM
You shouldn't really have notchy diffs in all honesty. This design of Schumacher diff has been in use for some time - and with the kit suppplied plates should be very good. I guess it's tough to say for me, as you have the diffs in your hands and i don't!!

chris68nufc 19-09-2008 10:45 PM
Cheers. Im sure that there will be somebody at Worksop next weekend that can have a look for me??? Mine is the Lipo version. Does anybody have a starting setup for Worksop indoors?

Mossy 19-09-2008 11:20 PM
Check the setup thread, ive posted what i will start on there.

Si

RSharpy 19-09-2008 11:40 PM
Si, do you run a diff and fixed center one way on all tracks?


All times are GMT. The time now is 05:56 AM.
Page 7 of 13 « First 56 7 89 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
oOple.com