oOple.com Forums - Electric Install Pics

oOple.com Forums (http://www.oople.com/forums/index.php)

- Team Durango (http://www.oople.com/forums/forumdisplay.php?f=80)

- - Electric Install Pics (http://www.oople.com/forums/showthread.php?t=31939)

Quote:

Originally Posted by offroadrc (Post 315613)

this is how it's in my durango:http://www.oople.com/forums/picture....pictureid=2645

dat moet toch wel beter en mooier jasper !!!!

which motor on a 21 did he run?

Quote:

Originally Posted by Chequered Flag Racing (Post 316284)

SpeedPassion & V3 motor Issue

Played pit bitch on Sunday for pal with the Durango

Electrics were installed much as the pics in previuos posts

Make sure the motor leads aren't touching / pressing the sensor lead were it plugs into the motor. Tried all sorts to resolve a cogging issue with the new esc / motor combo by retuning to tranny, throttle dead band, esc tune via programmer. Not until R4 did we cure it by routing two of the motor wires over the prop shaft so they didn't touch the senor cable. Think he's going to fit smaller wire dia and a mm or two longer so they have a bit more flex so as not to foul the sensor lead in future.

So R4 came and he didn't have to clean a run but still put on pole in the A. In the final he just drove away from the field.

Never touched the car setup that Hulk uses with mini-pins and just ran it as was.
Two screws backed out of the camber links as they hadn't been thread locked in.
Drive shaft pin popped out. Pushed back in and stayed put.

Motor as per kit geared on 21/87. Motor and esc temp OK. Maybe go down one or two next time out to see haw it goes.

I'm running a v3 along side a tekin rs pro. the cables all run together under the prop-shaft and im having no issues like that. im running 16gauge wire though.

Here's my revised layout: http://www.flickr.com/photos/mark799...7622883276035/

I found if there's too much bendy-ness in the wires the push the speedo up off its sticky tape. I can also mount it more inboard now too so i can get the shell well clear.

achja, het werkt zo goed, ik heb trouwens de body van de xx4 erop zitten. lol:

http://www.youtube.com/watch?v=uqgp0VBJ0pY

De groenten, Japser

here my elec installed ..
novak gtb esc running 5.5 bl novak motor

http://img.photobucket.com/albums/v1...i/DSC_0035.jpg

Here is my layout. :thumbsup: Loads of room!

http://mitchee.com/rc/dex4102.jpg

Quote:

Originally Posted by Big G (Post 320499)

which motor on a 21 did he run?

just found your reply

he was using a SP ESC & V3 6.5

now he's got he's got a GM ESC & Motor in and reports no issue. Finished 4th tin the C final at Worksop just gone. Myabe because I wasn't there to interfere :lol:

I'd love to see Oliv996's take on this car :)

Quote:

Originally Posted by Garry Driffill (Post 323965)

I'd love to see Oliv996's take on this car :)

Hi Garry !!!
Send me one and let see how I could deal with it :lol::woot:

Quote:

Originally Posted by gazbaz2 (Post 322916)

http://i600.photobucket.com/albums/t...g?t=1261394927

Might be worth swapping the battery link wires to the inside as the 2 main esc power wires in the centre are very close and could touch in an accident.

Something similar happened to me a few years back and ive been paranoid ever since..LOL

Nice layout tho,

Jamie.......

Quote:

Originally Posted by Oliv996 (Post 324078)

Hi Garry !!!
Send me one and let see how I could deal with it :lol::woot:

:lol: hahaa!! Alright then! :woot:

My install.
The Futaba 4PK receiver leaves little room in the 410, but it works! :thumbsup:

http://img.photobucket.com/albums/v1.../DSCN0388b.jpg

nice, good thing that your esc is so small.

Quote:

Originally Posted by thomj316 (Post 324100)

I know what you mean but in fact there well away from it, you just cant see it in the pic lol

Quote:

Originally Posted by offroadrc (Post 324432)

nice, good thing that your esc is so small.

Very! :thumbsup: I can't give up the 4PK!

Quote:

Originally Posted by gazbaz2 (Post 324449)

I know what you mean but in fact there well away from it, you just cant see it in the pic lol

If you connect the batts this way, the link between them will be close, while the the neg and pos connectors will be farther apart, and more importantly, safer. Batts are relatively cheap when compared to a DEX410, and the love we put in to them. :wub

http://img.photobucket.com/albums/v1.../DSCN0377b.jpg

Quote:

Originally Posted by HyperFX (Post 324386)

My install.
The Futaba 4PK receiver leaves little room in the 410, but it works! :thumbsup:

http://img.photobucket.com/albums/v1.../DSCN0388b.jpg

Hi, have you had any thermal issues with your rs pro with a 5.5?

I noticed when I ran the rs pro in my bmax, that the speedo got hotter than other speedies eg. lrp, novak.

I think maybe you could even reverse the direction of your speedy by 180, and put a fan facing the post.