Nice looking car there Thomas! That video of it on you tube is good, goes really well! Looks like a 10th car going round!

Just got this built and tested it out tonight, goes so well! :wub

I have entered the Micro National at Essex on Sunay so we shall see how we get on!

Im running, Savox 2057 MG, Logic RC 1300 40C Batt, Spek Micro RX and Ezrun 18t motor

http://i783.photobucket.com/albums/y...ng/RC18002.jpg

http://i783.photobucket.com/albums/y...ng/RC18001.jpg

Looks good Mark.

Here is pic of mine very close to finished.

Duratrax 1800mah 30C hard case lipo, Savox 0257 servo, EZRUN 25A ESC and 5200KV motor, Spektrum micro receiver, MRT PTX Transponder,

It's also sporting MIP CVD's, Ball Diffs, Titanium Tie-Rods, Sway bars and Losi Street tires with firm inserts. Tires are not glued yet as I'm waiting for a set of Narrow front rims.

That is an Exotek wing on the rear and the buggy body should be painted this weekend.

I'm also building an exact replica for my son but he will be running the truck body and wide Losi tires front and rear!!

Top diff= RC18B2 Stock balldiff
Below= RC18B MIP Superdiff
http://i123.photobucket.com/albums/o...2/DSC_0406.jpg
Mounted
http://i123.photobucket.com/albums/o...2/DSC_0404.jpg
http://i123.photobucket.com/albums/o...2/DSC_0405.jpg
What i can see,and feel, this will work, ace!!..sadly i had no extra MIP outdrives for rear, so i tock a stock RC18B (gen1) plastic outdrives and mounted them..no problem at all...

Hi,

Does the Exotek servo mounts fit 100% on the RC18B2?
http://www41.instantestore.net/merch...rvo_mounts.cfm

And will this servo fit the Exotek servo mounts perfectly?
http://www.rcmart.com/catalog/rc-ser...r-p-32620.html

Thanks!
Greetings,

the exotek servo mounts fit great running them in mine with a savox servo with no problems at all

So what Savox servo are you using and did they fit the mounts without modding? And did the servo saver fit without modding?

Does someone know if one of these servos will fit (again, without modding)
http://www3.towerhobbies.com/cgi-bin...&I=LXSWC4&P=ML

http://www.amainhobbies.com/product_...cro-Heli-Servo

Greetings,

i am using the sh 0257 servo and an xtm servo saver part number xtm3860
some peolpe do ust the kit saver but the splines dont match up but you can make it it fit

How do you get servo adapter over the spline?

None of the four adapters fit the splines. Before I saw this I called CML and they knew nothing, and told me the Futaba one fits (er, no, it's too large):o

Many thanks

Dave

Right, I've ditched the Savox, and gone for the straight fit AE one. But can anyone tell me if the Reedy can is a straight fit, and will I have problems with the pinion rubbing? or do I need the 66t spur to eliminate this?

Thanks

:wtf: RIP thread

Hi,

Does somone wants a RC18T??
I'm selling one,
If you have some interess, send me a pm.

Thanks,
Martijn

looking for hex screws to replace the Philips head ones (especially those tinny M2)
any ideas where to get them?

Have you tried http://modelfixings.com/ ?

thanks for the info, will check it out
cheers

great place, they have all that's needed, order placed, thank's again for sharing

Which exotek conversions would fit my rc18b2?

Just the shock towers I believe.

Thought there is a very sexy looking carbon double deck chassis conversion from AE's Factory Team which I have seen advertised in the States :drool: